Cub Cadet 23HP Z-Force 50 Lawn Mower User Manual


 
19
must be off, the parking brake must be
engaged, and both steering levers must be
opened-out to the side in the neutral position.
Once the engine is started, the seat must be
occupied and the parking brake must be
released before either of the steering levers is
folded up to the operating position or the
engine’s electronic ignition will be grounded
out and the engine will stop. Also, the seat
must be occupied before the blade clutch
switch can cause the blades to rotate.
8.
Safety Switch Operation Checks:
The fol-
lowing operational checks should be made
daily.
a.
Blade Clutch Switch:
Sit in the operator’s
seat. With both steering levers opened-out
in the neutral position and the parking
brake engaged, turn the blade clutch
switch “on” and try to start the engine. The
engine should not start. If it does, the blade
clutch switch must be replaced. If the
engine does not start, turn the blade clutch
switch “off” and start the engine. Now turn
the blade clutch switch “on” and the blades
should rotate. If the blades do not turn, the
blade clutch switch must be replaced, the
seat switch must be replaced or the elec-
tric PTO clutch must be repaired. The air-
gap should be checked every 200 hrs. (or
less, if severe operating conditions exist
such as when there are many on/off
cycles, mulching operations, material col-
lection systems used, and dusty/dirty con-
ditions), and the air-gap adjusted if more
than 0.035". To inspect, remove the “nega-
tive” cable from the battery and all spark-
plug wires. The air-gap should be checked
with feeler gages in the three slots of the
BBC. The air-gap should be adjusted to
0.013" to 0.015". There are three inspec-
tion slots I the brake cover. To adjust, suc-
cessively tighten each of the three gap
adjustment nuts an equal amount. Insert a
feeler gage (0.013" to 0.015") into each
slot as the air gap adjustment nut are tight-
ened. The correct adjustment occurs when
slight contact with the feeler gage occurs.
Engage the BBC a couple of times, and re-
check the air-gap. If it is not between
0.013" and 0.015", repeat the adjustment
procedure.
b.
Parking Brake Switch:
Sit in the opera-
tor’s seat. With both steering levers
opened-out in the neutral position and the
blade clutch switch “off”, release the park-
ing brake and try to start the engine. The
engine should not start. If it does, the park-
ing brake switch must be repositioned or
perhaps replaced. If the engine does not
start, engage the parking brake and start
the engine. Swing one steering lever up to
the operating position and the engine
should stop. If the engine does not stop,
the parking brake switch must be reposi-
tioned or replaced.
c.
Left and Right Steering Lever Switches:
Sit in the operator’s seat. With both steer-
ing levers opened-out in the neutral posi-
tion, the parking brake engaged and the
blade clutch switch “off”, swing the left
steering lever up to the operating position
and try to start the engine. The engine
should not start. If it does, the left steering
lever switch must be repositioned or per-
haps replaced. Open the left steering lever
to the neutral position and swing the right
steering lever up to the operating position
and try to start the engine. The engine
should not start. If it does, the right steer-
ing lever switch must be repositioned or
perhaps replaced. If the engine does not
start, open the right steering lever to the
neutral position and start the engine.
Swing the left steering lever up to the oper-
ating position and the engine should stop.
If the engine does not stop, the left steering
lever switch must be repositioned or
replaced. Open the left steering lever out to
the neutral position and start the engine.
Swing the right steering lever up to the
operating position and the engine should
stop. If the engine does not stop, the right
steering lever switch must be repositioned
or replaced.
d.
Seat Switch:
With both steering levers
opened-out to the neutral position, the
parking brake engaged and the blade
clutch switch in the “off” position, start the
engine. Now release the parking brake,
hold down on the back of the operator’s
seat against spring pressure, and swing
one of the steering levers up to the operat-
ing position. Release the operator’s seat
and the engine should stop. If the engine
does not stop, the seat switch must be
replaced. With both steering levers folded
out in the neutral position, the parking
brake engaged and the blade clutch switch
in the “off” position, sit in the operator’s
seat and start the engine. Turn the blade
clutch switch to the “on” position and the
blades should start to rotate. Raise up
slightly off the operator’s seat and the
blades should stop. If the blades do not