Filter
Top Products
OPERATUON
TURNING
. Release the drive control bar.
• Move throttle control to "SLOW" position
• Place shift lever indicator in "F" (forward) position.
Tines wilt not turn.
. Lift handle to raise tines out of ground.
• Swing the handle in the opposite direction you wish to
turn, being careful to keep feet and legs away from
tines,
• When you have completed your turn-around, release
the drive co ntrol bar and lower handler Place shift lever
in "T" (till) position and move throttle control to desired
speed. To begin tilling, hold drive control bar against
the handle.
OUTER SIDE SHIELDS (See Fig, 11)
The front edges of the outer side shields are slotted so that
the shields can be raised for deep tilling and lowered for
shallow titling to protect small plants from being buried.
Loosen nut "A" in slot and nut "B" Move shield to desired
position (both sides). Retighten nuts.
TRANSPORTING
......................................... i
_ CAUTION: Before lifting or transport-
ing, allow tiller engine and muffler to
cool. Disconnectsparkplugwireo Drain
gasoline from fuel tank,
• Release the depth stake pin Move the depth stake
down to the top hole for transporting the tiller. Place
depth stake pin in hole of depth stake to lock in position,
This prevents tines from scuffing the ground
° Place shift lever indicator in "F" (forward) position for
transporting.
• Hold the drive controt bar against the handle to start
tiller movement Tines will not turn,
• Move throttle control to desired speed
BEFORE STARTING ENGINE
IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT
TO ENTER THE ENGINE WHEN CHECKING OR ADDING
OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE
IN APPROVED, CLEAN, COVERED CONTAINERS, USE
CLEAN FiLL FUNNELS.
CHECK ENGINE OIL LEVEL (See Fig. 12)
• The engine in your unit has been shipped, from the
factory, already filfed with SAE 30 summer weight oil,
• With engine level, clean area around oil filler plug and
remove plug,
• Engine oil should be to point of overflowing° For
approximate capacity see "PRODUCT SPECIFICA-
TIONS" on page 3 of this manual. All oil must meet
AP]. Service Classification SG.
• For cold weather operation you should change oil for
easier starting (See oil viscosity chart in the Customer
Responsibilities section of this manual).
• To change engine oil, see the Customer Responsibili-
ties section in this manual,
OIL
OIL
FILLER
PLUG
IL DRAIN
PLUG
FIG. 12
ADD GASOLINE
• Fill fuel tank. Use fresh, clean, regular unleaded
gasoline, (Use of leaded gasoline will increase carbon
and lead oxide deposits and reduce valve life.
IMPORTANT; WHEN OPERATING iN TEMPERATURES
BELOW 32°F (0°C), USE FRESH, CLEAN, WINTER
GRADE GASOLINE TO HELP INSURE GOOD COLD
WEATHER STARTING.
WARNING: Experience indicates that alcohol blended
fuels (called gasohof or using ethanol or methanol) can
attract moisture which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage To avoid engine
problems, the fuel system should be emptied before stor-
age of 30 days or longer. Drain the gas tank. start the
engine and let it run until the fuel lines and carburetor are
empty_ Use fresh fuel next season, See Storage section
of this manual for additional information. Never use engine
or carburetor cleaner products inthe fuel tank or permanent
damage may occur
i l/l/, ill/ iiiuii, 1,1,,,,,,,,i,
CAUTION: Fill to within 1/2 Inch of top
of fuel tank to prevent spills and to
allow for fuel expansion. If gasoline Is
accidentally spilled, move machine
away from area of spill. Avoid creatlng
any source of ignition until gasoline
vapors have disappeared.
Do not overfill. Wipe off any sptlled oil
or fuel. Do not store, spill or use gaso-
line near an open flame.
. / i ,i J ,ill,, ,,,i,,,,,i,,
11