Filter
Top Products
Pressure Washers
9
Operation (Continued)
2. The easiest way to regulate the cleaning power of your
pressure washer is by changing the distance from the
surface you are cleaning. Begin spraying with a wide fan
pattern while standing several feet from the surface.
Slowly move closer to the object you are cleaning,
adjusting the spray pattern as necessary, until you find
the most effective cleaning technique.
The final rinse should start at the bottom and work upward.
Make sure that you thoroughly rinse the surface and that you
remove all detergent.
To reduce the risk of bodily injury or property damage, always
follow this procedure whenever spraying is stopped, when work
is completed, and before checking or repairing any part of the
system.
1. Engage the trigger safety latch.
2. Turn the unit off.
3. Remove the ignition cable from the spark plug.
4. Shut off the water supply.
5. Disengage the trigger safety latch and trigger the gun to
relieve pressure.
6. Re-engage the trigger safety latch.
7. Before overnight storage, long term storage, or transporting
unit, disconnect the water supply and turn off the fuel supply
valve.
1. Be sure all detergent is flushed from system.
2. Turn the engine OFF.
3 Turn the water supply OFF.
4. After the engine and water supply are turned off, trigger the
gun to depressurize the system.
NEVER turn the water supply off before
turning the engine/motor off. Serious
damage could occur to the pump and/or engine/motor.
NEVER disconnect the high pressure
discharge hose from the machine while the
system is pressurized. To depressurize, turn engine/motor off, turn
water supply off and squeeze gun trigger 2-3 times.
5. After each use, wipe all surfaces of the pressure washer with
a clean, damp cloth.
• Do not store the pressure washer outdoors.
• Do not store the pressure washer where it might freeze
unless it has been properly winterized.
!
CAUTION
NOTICE
www.chpower.com
LONG TERM STORAGE INSTRUCTIONS (MORE THAN 30 DAYS
IN STORAGE)
1. Remove fuel from the tank and run the pressure washer in a
normal operating mode until the engine stops from a lack of
fuel. Normal operating mode means actually spraying water
from the gun while the engine is running.
Alternate method – Add fuel stabilizer to gas in the tank and
run in normal operating mode for at least five minutes.
2. Stop the engine, turn off the water supply, and trigger the
gun to release pressure in the high-pressure hose.
3. Disconnect the water supply and high pressure hose from the
pump.
4. Allow the engine to cool.
5. Disconnect the spark plug wire and remove the spark plug.
6. Pour 1/2 oz. of engine oil into the spark plug hole.
Never pull the starter rope on the engine
when the spark plug is removed unless the
spark plug hole is covered. Fuel vapor from the hole can ignite by
a spark.
7. Place a rag over the spark plug hole and slowly pull the
starter rope several times to distribute the oil.
WINTERIZING INSTRUCTIONS
1. Follow and complete the Long Term Storage Instructions
above.
2. Disconnect the spark plug wire.
3. Disconnect the high pressure hose from the pump.
4. Insert a 12” to 14” piece of garden hose into the pump inlet.
5. Place a funnel in the other end of the garden hose.
Read the manufacturer’s instructions for
safe handling and disposal of RV antifreeze.
6. Pour approximately 6 oz. of RV antifreeze into the funnel.
7. Pull the starter rope several times until the RV antifreeze
comes out of the pump outlet.
8. Disconnect the high pressure hose from the gun and drain
the hose. Hold the gun and lance in a vertical position and
squeeze the trigger to drain the water out.
TIPS FOR EXTENDING THE LIFE OF YOUR PRESSURE WASHER
1. Never operate the unit without water.
2. Your pressure washer is not meant to pump hot water. Never
connect your pressure washer to a hot water supply as it will
significantly reduce the life of the pump.
3. Running the unit for more than one minute without spraying
water causes heat to build up in the pump. Running the unit
without spraying water can damage pump components.
4. Release the trigger prior to switching the lance between high
and low pressure. Failure to do so may reduce the life of the
o-rings in the lance.
NOTICE
!
WARNING
9. Storage
6. Final Rinse
7. Pressure Relief Procedure
8. Shutdown