Yard-Man 31AH553G401 Snow Blower User Manual


 
10
SECTION 4: OPERATING YOUR SNOW THROWER
Before Starting
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
The spark plug wire was disconnected for safety.
Attach spark plug wire to spark plug before starting.
Make certain the auger and drive clutch levers are
in the disengaged (released) position.
Check oil and gasoline level and add if necessary.
Follow related instructions in the seperate engine
manual packed with your snow thrower.
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel the machine indoors or while the
engine is hot or running. Extinguish cigarettes,
cigars, pipes and other sources of ignition.
To Start Engine
Make certain the fuel cut-off valve is in OPEN
position.
Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not turn key
.
NOTE: Engine will not start unless ignition key is
inserted into ignition slot in the carburetor cover.
Electric Starter
WARNING: The electric starter is equipped
with a grounded three-wire power cord and
plug, and is designed to operate on 120 volt
AC household current. It must be used with a
properly grounded three-prong receptacle at
all times to avoid the possibility of electric
shock. Follow all instructions carefully prior to
operating the electric starter.
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
If your house wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
If your home electrical system is grounded, but
a three-hole receptacle is not available, one should
be installed by a licensed electrician before using
the electric starter.
If you have a grounded three-prong receptacle,
proceed as follows.
Rotate choke knob to FULL position.
Push primer two or three times for cold engine start.
Connect power cord to switch box located on top of
engine. Plug the other end of power cord into a
three-prong 120-volt, grounded, AC receptacle.
Push starter button on the switch box to crank
engine. As you crank the engine, move choke knob
to FULL choke position.
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF again.
When disconnecting the power cord, always unplug
from the three-prong receptacle first, and then from
the snow thrower.
Recoil Starter
Rotate choke knob to FULL choke position (cold
engine start).
If engine is warm, place choke in OFF position
instead of FULL.
Push primer button two or three times for cold
engine start.
If engine is warm, push primer button only once.
NOTE: Always cover vent hole in primer button when
pushing. Additional priming may be necessary for first
start if temperature is below 15 degrees Fahrenheit.
Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.
As engine warms up and begins to operate evenly,
rotate choke knob slowly to OFF position. If engine
falters, return to FULL choke, then slowly move to
OFF position.
To Stop Engine
To stop engine, remove the ignition key. Do not turn
key. Disconnect the spark plug wire from the spark
plug to prevent accidental starting while equipment
is unattended.
To help prevent possible freeze-up of starter, proceed
as follows:
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
Electric Starter: Connect power cord to switch box
on engine, then to 120 volt AC receptacle. With the
engine running, push starter button and spin the
starter for several seconds. The unusual sound
made by spinning the starter will not harm engine or
starter. Disconnect the power cord from receptacle
first, and then from switch box.