Worksaver SDM40-60 Brush Cutter User Manual


 
25
14
SAFETY INSTRUCTIONS (continued)
After servicing, be sure all tools, parts and service equipment are removed.
Check to ensure all safety signs are installed and in good condition. (See safety sign section for location
drawing.)
Do not allow grease or oil to build up on any deck or platform.
Never replace hex bolts with less than grade five bolts unless otherwise specified, i.e. shear bolts. Refer to
bolt torque chart for head identification marking.
Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement
parts must be used to restore your equipment to original specifications. The manufacturer will not claim
responsibility for use of unapproved parts and/or accessories and other damages as a result of their use.
If equipment has been altered in any way from original design, the manufacturer does not accept any liability
for injury or warranty.
A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance on this
equipment.
Following operation, or when unhooking, stop the tractor, set the brakes, disengage the PTO, shut off the
engine and remove the ignition keys.
Never unhitch without using the tongue jack. The tongue is very heavy. Attempting to lift the tongue without
using the tongue jack could cause strains. Allowing the tongue to fall suddenly and unexpectedly could result
in crushing injury. Use the tongue jack for lifting the cutter only. Overloading the jack can cause failure with
possible serious bodily injury or even death.
Store the unit in an area away from human activity.
Do not park equipment where it will be exposed to livestock for long periods of time. Damage and livestock
injury could result.
Do not permit children to play on or around the stored unit.
Make sure all parked machines are on a hard, level surface and engage all safety devices.
If blocking is used, make sure it is solid and secure before leaving area.
MAINTENANCE SAFETY (continued)
STORAGE SAFETY
BLADE BEAM & GEARBOX
INSTALLATION
A. Raise cutter using tractor 3-point lift. Turn off tractor
engine.
B. BLOCK CUTTER SECURELY INTO POSITION.
C. Remove cotter pin and blade holder retaining nut.
Wear heavy work gloves to protect hands from sharp
edges.
D. Grasp blade holder and pull off shaft. If necessary,
align blade bar with access hole in top of deck and
drive off with hammer and pipe. Care should be taken
not to damage threads on blade bolt.
E. Press all three tabs and slide yoke shield back.
F. Remove shear bolt and retaining clip. Slide yoke off
gearbox input shaft.
G.Remove nuts securing gearbox to deck. Remove
gearbox.
C. Attach gearbox to cutter deck using bolts and nuts.
D. Install blade holder onto gearbox securing with
castellated nut and flat washer. Torque nut to 350
ft./lbs. Wear heavy work gloves to protect hands from
sharp edges.
E. Install cotter pin to retain nut. It may be necessary to
slightly loosen nut to install cotter pin.
F. Slide driveline yoke onto gearbox input shaft. Install
retaining clip and shear bolt.
G.Lock driveline yoke shield securely into place.
H. Fill gearbox with oil to proper level.
OWNER SERVICE (continued)
R E PAIR OF OPTIONAL
CHAIN SHIELDING
Inspect chain shielding each day of operation and
replace any broken or missing chains as required.
BLADE BEAM & GEARBOX
REMOVAL
A. Raise cutter using tractor 3-point lift. Turn off tractor
engine.
B. BLOCK CUTTER SECURELY INTO POSITION.
W ARNING!
DO NOT GET UNDER CUTTER UNLESS IT IS
SECURELY BLOCKED IN POSITION. ACCIDENTAL
FALL COULD CAUSE SERIOUS INJURY OR DEATH.
W ARNING!
DO NOT GET UNDER CUTTER UNLESS IT IS
SECURELY BLOCKED IN POSITION. ACCIDENTAL
FALL COULD CAUSE SERIOUS INJURY OR DEATH.
W ARNING!
FAILURE TO INSTALL RETAINING CLIP WILL
ALLOW DRIVELINE TO SWING FREELY IF BOLT IS
SHEARED CAUSING POSSIBLE INJURY OR DEATH.
U Keep children away from danger all day, every day.
U Equip tractors with roll-over protection (ROPS) and keep all machinery
guards in place.
U Please work, drive, play, and live each day with care and concern for your
safety and that of your family and fellow citizens.