Filter
Top Products
-- 3 --
disconnected. Keep v ents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
D
Neverplace anyobject in t heair intakeopen-
ing as this could restrict proper air flow and
cause dam age to the unit.
D
Never use for spreading chemicals, fertiliz-
ers,orother substances which maycontain
toxic materials.
D
Toavoid spreading fire, donot use nearleaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
D
Use only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
D
Have all maintenance other than the r ec-
ommended procedures described in thein-
struction manual performed by an autho-
rized service dealer.
D
Disconnect spark plug bef or e perform ing
maintenance except for carbur etor adjust-
ments.
D
Use only recommended Weed Eater
!
re-
placement parts; use of any other parts
may void yourwarranty and cause damage
to your unit.
D
Empty fuel tank before storing the unit. Use
upfuelleft i ncar bur etorbystarting engi neand
letting it r u n until it stops .
D
Do not use any accessory or attachment
other than those recommended by manufac-
turer for use with y our unit.
D
Do not store the unit orfuel ina closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D
Store in a dry area out of reach of children.
SPECIAL NOTICE:
Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather hasbeen linked toblood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this t ool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE:
For use r son U.S. For-
est Land and in some states, including Cali-
fornia (Public Resources Codes 4442 and
4443), Idaho, Maine, Minnesota, NewJersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush, and/orgrass covered landin the above
areas are required to be equipped with a
spark arresting screen, maintained in effec-
tive working order, or the engine must becon-
structed, equipped, and m aintained for the
prevention of fire. Check with yourstate orlo-
cal authorities for regulations pertaining to
these requirements. Failure to follow these
requirements isa v iolation of the law.This unit
is not factory equipped with a spark arresting
screen; however, a spark arresting screen is
available asan optional part. If aspark arrest-
ing screen is required in your area, contact
your authorized service dealer for the correct
kit. The spark arresting screen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance w ith regulation s.
ASSEMBLY
WARNING:
Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
WARNING:
If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
D
A standard screwdriver is required for as-
sembly.
BLOWER TUBE ASSEMBLY
D
Align the rib on the blower tube with the
groove in the blower outlet; slide the tube
into place.
NOTE:
Tubeclamp must beloose enough to
allow blower t ubeto beinserted in blower out -
let. Loosen tube clamp byturning knob coun-
terclockwise.
Blower
Tube
Blower
Outlet
Rib
Groove
D
Tighten the tube clamp b y turning the knob
clockwise.
D
To remove the tube, turn the knob counter-
clockwise to loosen clamp; remove tube.
VACUUM BAG ASSEMBLY
D
Open the zipper on the vacuum bagand in-
sert the elbow tube.
D
Push the small end of the elbow tube
through the small opening in the bag.
Small
Opening
Zipper
Opening
Elbow
Tube
Rib
NOTE:
Make sureedgeof the smallopening
is flush against the flared area of the elbow
tube, and the rib on the elbow tube is on the
bottom.