Filter
Top Products
self or your clothes which can ignite. Wash
your skin and change clothes immediately.
a) Use only an approved gasoline con
-
tainer.
b) Never fill containers inside a vehicle or
on a truck or trailer bed with a plastic
liner. Always place containers on the
ground away from your vehicle before
filling.
c) When practical, remove gas-powered
equipment from the truck or trailer and
refuel it on the ground. If this is not
possible, then refuel such equipment
on a trailer with a portable container,
rather than from a gasoline dispenser
nozzle.
d) Keep the nozzle in contact with the rim
of the fuel tank or container opening at
all times until fueling is complete. Do
not use a nozzle lock-open device.
e) Extinguish all cigarettes, cigars, pipes
and other sources of ignition.
f) Never fuel machine indoors.
g) Never remove gas cap or add fuel
while the engine is hot or running. Al-
low engine to cool at least two minutes
before refueling.
h) Never over fill fuel tank. Fill tank to no
more than ½ inch below bottom of filler
neck to provide space for fuel expan-
sion.
I) Replace gasoline cap and tighten se-
curely.
j) If gasoline is spilled, wipe it off the en
-
gine and equipment. Move unit to
another area. Wait 5 minutes before
starting the engine.
k) Never store the machine or fuel con
-
tainer inside where there is an open
flame, spark or pilot light as on a water
heater, space heater, furnace, clothes
dryer or other gas appliances.
l) To reduce fire hazard, keep machine
free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage
and remove any fuel soaked debris.
m) Allow machine to cool at least 5 min
-
utes before storing.
GENERAL SERVICE:
•
Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains car
-
bon monoxide, an odorless and deadly gas.
•
Before cleaning, repairing, or inspecting,
make certain the blade and all moving parts
have stopped. Disconnect the spark plug
wire and ground against the engine to pre
-
vent unintended starting.
•
Check the blade and engine mounting bolts
at frequent intervals for proper tightness.
Also, visually inspect blade for damage
(e.g., bent, cracked, worn) Replace blade
with the original equipment manufacturer’s
(O.E.M.) blade only, listed in this manual.
“Use of parts which do not meet the original
equipment specifications may lead to im
-
proper performance and compromise
safety!”
•
Mower blades are sharp and can cut. Wrap
the blade(s) or wear gloves, and use extra
caution when servicing them.
•
Keep all nuts, bolts, and screws tight to be
sure the equipment is in safe working con
-
dition.
•Never tamper with safety devices. Check
their proper operation regularly.
•After striking a foreign object, stop the en-
gine, disconnect the spark plug wire and
ground against the engine. Thoroughly in-
spect the mower for any damage. Repair
the damage before starting and operating
the mower.
•Grass catcher components, discharge
cover, and trail shield are subject to wear
and damage which could expose moving
parts or allow objects to be thrown. For
safety protection, frequently check compo
-
nents and replace immediately with original
equipment manufacturer’s (O.E.M.) parts
only, listed in this manual. “Use of parts
which do not meet the original equipment
specifications may lead to improper perfor
-
mance and compromise safety!”
•
Do not change the engine governor setting
or overspeed the engine. The governor con
-
trols the maximum safe operating speed of
the engine.
•
Maintain or replace safety and instruction la
-
bels, as necessary.
•
Observe proper disposal laws and regula
-
tions. Improper disposal of fluids and
materials can harm the environment.
SI-102
1.17.02
5