Filter
Top Products
Add En{jineOil and Fuel
• Place pressure washer on a level surface•
NOTE:Verify provided oil bottle is the correct viscosity for
current ambient temperature•
• Referto engine operator's manualand follow oil and
fuel recommendations and instructions•
NOTICE
Any attempt to crank OFstart the engine before it has been
properly filled with the recommended oil will result in
_ment failure•
Referto enginemanualfor oilandfuel fill information•
Damageto equipmentresultingfromfailureto followthis
instructionwill voidwarranty•
NOTE:Checkoil often during engine break-in• Referto
engine operator's manual for recommendations•
Connect Hoseand Water Supply to Pump
NOTICE
DO NOTFunthe pump without the water supply connected
and turned on. _ _ _ m
I" Damagetoequipmentresultingfromfailureto followthis
h instructionwill voidwarranty•
NOTE:Removeand discard the shipping caps from the
pump's high pressure outlet and water inlet before attaching
hoses•
1. Uncoil high pressure hoseand attachone end of hose
to baseof spray gun. Tighten by hand•
WARNING
The high pressurestream of water that this
_ quipment produces can cut through skin and its
underlying tissues, leadingto serious injury and
3ossible amputation•
• NEVERconnecthighpressurehoseto nozzleextension•
, Keephighpressurehoseconnectedto pumpandspraygun
whilesystemis pressurized•
, Alwaysbecertainspraygun,nozzlesandaccessoriesare
correctlyattached•
2. Attach other end of high pressure hoseto high
pressure outlet on pump• Tighten by hand•
3. Run water through your garden hose for 30 seconds to
clean out any debris•
IMPORTANT:DONOTsiphon standing water for the water
supply• UseONLYcold water (less than I O0°F).
4. Beforeconnecting garden hose to water inlet, inspect
inlet screen (A). Cleanscreen if it contains debris or
have it replacedif damaged•DONOTFunpressure
washer if inlet screen is damaged•
5. Connectthe garden hose (not to exceed50 feet in
length) to the water inlet• Tighten by hand•
NOTICE
Damageto pump or water inlet connector will occur if a
OneWay Valve (vacuumbreaker or check valve) is
connected to pump•
ThereM/USTbeat leastten feet(31Vl)of unrestrictedgarden
hosebetweenthe pressurewasherinletandanydevice,suchas
aOneWayValve•
Damageto equipmentcausedby attachinga OneWayValveto
pumpwill voidwarranty•
6. Turn ON the water and squeezethe trigger on the spray
gun to purge the pump system of air and impurities•
WARNING
Risk of eyeinjury.
• _ ISpray can splash back or propel objects•
Alwayswearsafetygoggleswhenusingthis equipmentor in
vicinityof whereequipmentisin use.
Beforestartingthepressurewasher,besureyouarewearing
adequatesafetygoggles•
NEVERsubstitutesafetyglassesfor safetygoggles•
Checklist Before Starting Engine
Review the unit's assembly to ensure you have performed all
of the following•
1. Be sureto readthe Operator Safetysection and How to
Use Your Pressure Washerin Operationsection before
using pressure washer•
2. Make sure handle is in placeand secure•
3. Checkthat oil has been addedto proper levelin the
engine crankcase•
4. Add proper fuel to fuel tank•
5. Checkfor properly tightened hose connections•
6. Checkto makesure there are no kinks, cuts, or damage
to high pressure hose•
7. Providea proper water supply at an adequateflow•
CD
3