Filter
Top Products
www.tanaka-usa.com 3 custsvc@tanaka-ism.com
Owner’s Manual
TPS-2501,TPS-2510.TPS-250PN,TPS-270PN
2. Warnings and safety instructions
Operator Safety
• Always wear head protection with full face shield to help
protect against falling branches and debris.
• Avoid all power lines. This unit is not insulated against
electrical current.
• Gloves should be used when sharpening chain.
• Always wear heavy long pants, boots, and gloves. Do not
wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair so it is above shoulder length.
• Do not operate tool when you are tired, ill or under the
influence of alcohol, drugs or medication.
• Never let a child or inexperienced person operate the
machine.
• Wear hearing protection.
• Never start or run the engine inside a closed room or
building. Breathing exhaust fumes can kill.
• Keep handles free of oil and fuel.
• Keep hands away from cutting equipment.
• Do not grab or hold the unit by the cutting equipment.
• When the unit is turned off, make sure the cutting
attachment has stopped before the unit is set down.
• When operation is prolonged, take a break from time to time
so that you may avoid possible white-finger disease which is
caused by vibration.
• The operator must obey the local regulations of cutting area.
Unit/Machine Safety
• Inspect the entire unit/machine before each use. Replace
damaged parts. Check for fuel leaks and make sure all
fasteners are in place and securely tightened.
• Replace parts that are cracked, chipped or damaged in any
way before using the unit/machine.
• Keep others away when making carburetor adjustments.
• Use only accessories as recommended for this unit/machine
by the manufacturer.
• Never let the chain strike any obstacle.
If the chain makes contact, the machine should be stopped
and checked carefully.
• Make sure the automatic oiler is working.
Keep the oil tank filled with clean oil. Never let chain run dry
on the bar.
• All unit service, other than the items listed in the
operator's/owner's manual, should be performed by
competent chainsaw service personnel. (For example, if
improper tools are used to remove the flywheel or if an
improper tools is used to hold the flywheel in order to
remove the clutch, structural damage to the flywheel could
occur and could subsequently cause the flywheel to burst.)
WARNING!
Never modify the unit/machine in any way.
Do not use your unit/machine for any job except that for which it is
intended.
Fuel Safety
• Mix and pour fuel outdoors and where there are no sparks or
flames.
• Use a container approved for fuel.
• Do not smoke or allow smoking near fuel or the
unit/machine or while using the unit/machine.
• Wipe up all fuel spills before starting engine.
• Move at least 3 m (10 ft.) away from fueling site before
starting engine.
• Stop engine before removing fuel cap.
• Empty the fuel tank before storing the unit/machine. It is
recommended that the fuel be emptied after each use. If
fuel is left in the tank, store so fuel will not leak.
•
• Store unit/machine and fuel in area where fuel vapors
cannot reach sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
WARNING!
Anti-vibration systems do not guarantee that you will not sustain
white-finger disease or carpel tunnel syndrome. Therefore, continual
and regular users should monitor closely the condition of their hands
and fingers. If any of the above symptoms appear, seek medical
advice immediately.
Cutting Safety
• Do not cut any material other than wood or wooden objects.
• For respiratory protection, wear an aerosol protection mask
when cutting the wood after insecticide has been applied.
• Keep others including children, animals, bystanders and
helpers outside the hazard zone. Stop the engine
immediately if you are approached.
• Hold the unit/machine firmly with both hands.
• Keep firm footing and balance. Do not over-reach.
• Keep all parts of your body away from the muffler and
cutting attachment when the engine is running.
• Before pruning branches, the operator must be accustomed
to the pruning techniques of the machine.
• Be sure to pre-plan a safe exit from a falling objects.
• While cutting, hold the machine firmly with both hands with
thumb firmly locked around front handle, and stand with
feet well balanced and your body balanced.
• Be alert against kickback (when saw kicks up and back at
operator). Never cut with the nose of the bar.
Maintenance safety
• Maintain the unit/machine according to recommended
procedures.
• Disconnect the spark plug before performing maintenance
except for carburetor adjustments.
• Keep others away when making carburetor adjustments.
• Use only genuine Tanaka replacement parts as
recommended by the manufacturer.
WARNING!
Improper maintenance could result in serious engine damage or in
serious personal injury.
Transport and storage
• Carry the unit/machine by hand with the engine stopped and
the muffler away from your body.
• Allow the engine to cool, empty the fuel tank, and secure
the unit/machine before storing or transporting in a vehicle.
• Empty the fuel tank before storing the unit/machine. It is
recommended that the fuel be emptied after each use. If
fuel is left in the tank, store so fuel will not leak.
• Store unit/machine out of the reach of children.
• Clean the unit carefully and store it in a dry place.
• Make sure engine switch is off when transporting or storing.
• When transporting in a vehicle, cover chain with chain cover.
If situations occur which are not covered in this manual, take care and
use good judgment.
Contact your dealer if you need assistance.
Pay special attention to statements preceded by the following words:
WARNING!
Indicates a strong possibility of severe personal injury or loss of life, if
instructions are not followed.
CAUTION!
Indicates a possibility of personal injury or equipment damage, if
instructions are not followed.
NOTE!
Helpful information for correct function and use.