![](http://pdfasset.owneriq.net/3/e9/3e937633-5a47-4ef8-83d9-9a86437144ed/3e937633-5a47-4ef8-83d9-9a86437144ed-bg19.png)
Section 2 - OPERATING INSTRUCTIONS
2.1 PRE-START CHECK LIST
Make the following checks and perform the service
required before each start-up.
2.1.1. Check engine oil and add oil as needed to bring
level up to the FULL mark. Refer to engine owner's
manual for oil specifications
2.1.2. Check guards, chutes, deflectors and covers to
make sure all are in place and securely tightened.
2.1.3. Check auger control and wheel drive control
to insure cables are connected and both levers
operate freely. See Figure 2.1.
IMPORTANT: On 7 HP models only. Standing in the
operator's position, the left handle bar lever is for wheel
drive engagement and disengagement. The right handle
bar lever is for auger/impeller engagement and
disengagement. Hold both levers down to handle bar for
engagement and release levers for disengagement.
When both levers are pressed down to the handle bar at
the same time, the operator can release the right hand
lever and the right lever will remain engaged as long as
the left hand lever is held down to handle bar. Release
the left hand lever and both levers will disengage.
2.1.6. Add fuel to tank after pushing the machine
outside where fumes can safely dissipate. Make sure
cap is tightened after refueling. Wipe up any spilled
fuel on machine and surrounding area. Refer to
Engine Owners Manual for specifications.
2.1.7. Check auger housing and discharge chute,
both must be free of all obstructions. Clean engine of
any accumulation of spilled fuel, dirt, etc.
, WARNING
DO NOT use an electrical extension cord that is
damaged. A damaged electrical extension cord could
cause a shock or fire. Thoroughly inspect electrical
extension cord before using machine. If cord is
damaged, do not use and do not operate machine.
Replace damaged cord immediately. Contact your
Snapper service dealer for assistance. To reduce the
risk of electric shock, use only with an extension
cord intended for outdoor use having a cord type:
SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A or
SJTOW-A.
_ HEEL DRIVE
CONTROL
t4
AUGER/IMPELLER
CONTROL _ */
Q
FIGURE 2.1
2.1.4. Check chute operation. Rotate chute crank to
insure smooth rotation throughout its range.
2.1.5. Check tires and add or release air as needed
to bring air pressure to 12 psi without tire chains. Air
pressure with tire chains should be 16 psi.
WARNING
Use approved fuel container. DO NOT smoke near
open fuel container. DO NOT fill fuel tank indoors or
when engine is running. Allow engine to cool for at
least ten minutes before refilling. Wipe off any
spilled fuel before starting engine. DO NOT run
engine indoors.
IMPORTANT: Electric Start Kit optional accessory on
some models.
2.1.8. Check and make sure extension cord is in
good condition. Extension cord should not have any
broken insulation or exposed wires. Use an
extension cord that is heavy enough to carry the
correct amount of current to the machine. See
Figure 2.2 for correct size to use depending on cord
length and nameplate ampere rating. If in doubt,
use the next heavier gauge cord.
MINIMUM GAUGE FOR CORD SETS
120 or 230 Volt Total Length of Cord in Feet
Rating-Amps 25 ft. I 50 ft. I 100 ft. I 150 ft.
More Not More ,7,.,,,.,A.W.('_.
Than Than
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not
Recommended
FIGURE 2.2