Filter
Top Products
OPERATaON
!
The operation of any tractor can result in foreign objects thrown into the eyes, which can I
resultinsevereeyedamage. Alwayawearsafetyglassesoreyeshieldswhileoperatingyour |
tractor or performing any adjustments or repairs. We recommend a wide vision safety mask |
over the spectacles or standard safety glasses, ............. I{
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 8)
Your tractor isequipped with an operator presence sensing
switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
,, Depress clutch/brake pedal into full "BRAKE" position
and hold.
• Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal Pedal should
remain in"BRAKE" position. Make sure parking brake
will hold tractor secure.
ATTACHMENT CLUTCH
THROTTLE/ LEVER "ENGAGED"
CHOKE POSITION
"DISENGAGED"
POSITION
PARKING
BRAKE
"BRAKE" _"ENGAGED" GEARSHIFT
POSITION LEVER
CLUTCHIBRAKEPEDAL
"DRIVE"POSITION
"DISENGAGED"
_HEIGHT POSITION
ADJUSTMENT
KNOB
FIG. 8
STOPPING (See Fig. 8)
MOWER BLADES -
,' Move attachment clutch lever to "DISENGAGED" po-
sition.
GROUND DRIVE -
• Depress clutch/brake pedal intofull "BRAKE" position.
. Move gearshift lever to neutral (N) position.
ENGINE -
• Move throttle control to slow (€_S_,)position.
NOTE: Failure to move throttle control to slow (,_)
position and allowing engine to idle before stopping may
cause engine to "backfire":
. Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use_
,, Never use choke to stop engine_
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass areas.
_"---_UTION: Always stop tractor com_
_ pletely, as described above, before leav-
_ ing the operator's position; to empty
_ grass catcher, etc.
TO USE THRO'rrLE CONTROL (See Fig. 8)
Always operate engine at full throttle_
Operating engine at less than full throttle reduces the
battery charging rate.
Full throttle offers the best bagging and mower perfor-
mance.
TO MOVE FORWARD AND BACKWARD
(See Fig. 8)
The direction and speed of movement iscontrolled by the
gearshift {ever_
° Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position.
• Move gearshift lever to desired position.
• Slowly release clutch/brake pedalto start movemenL
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE,
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 8)
The cutting height iscontrolled by turning the height adjust-
ment knob in desired direction.
o Turn knob clockwise ((_) to raise cutting heightr
° Turn knob counterclockwise (F-"_)to lower cutting
height.
The cutting height range is approximately 1-1/2" to 4'L The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
o The average lawn should be cut to approximately 2-1/2
inches during the coot season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
° For best cutting performance, grass over 6 inches in
height should be mowed twice. Make the first cut
relatively high; the second to desired height.
13