Filter
Top Products
14 Cheetah 10K.7 SCSI Product Manual, Rev. D
is initiated. If cache operation is not enabled, the buffer (still segmented with required number of segments) is
still used, but only as circular buffer segments during disc medium read operations (disregarding Prefetch
operation for the moment). That is, the drive does not check in the buffer segments for the requested read
data, but goes directly to the medium to retrieve it. The retrieved data merely passes through some buffer seg-
ment on the way to the host. On a cache miss, all data transfers to the host are in accordance with buffer-full
ratio rules. On a cache hit the drive ignores the buffer-full ratio rules. See explanations associated with Mode
page 02h (disconnect/reconnect control) in the SCSI Interface Product Manual.
The following is a simplified description of a read operation with cache operation enabled:
Case A - A Read command is received and the first logical block (LB) is already in cache:
1. Drive transfers to the initiator the first LB requested plus all subsequent contiguous LBs that are already in
the cache. This data may be in multiple segments.
2. When the requested LB is reached that is not in any cache segment, the drive fetches it and any remaining
requested LBs from the disc and puts them in a segment of the cache. The drive transfers the remaining
requested LBs from the cache to the host in accordance with the disconnect/reconnect specification men-
tioned above.
3. If the prefetch feature is enabled, refer to Section 4.5.2 for operation from this point.
Case B - A Read command requests data, the first LB of which is not in any segment of the cache:
1. The drive fetches the requested LBs from the disc and transfers them into a segment, and from there to
the host in accordance with the disconnect/reconnect specification referred to in case A.
2. If the prefetch feature is enabled, refer to Section 4.5.2 for operation from this point.
Each buffer segment is actually a self-contained circular storage (wrap-around occurs), the length of which is
an integer number sectors. The wrap-around capability of the individual segments greatly enhances the
buffer’s overall performance as a cache storage, allowing a wide range of user selectable configurations, which
includes their use in the prefetch operation (if enabled), even when cache operation is disabled (see Section
4.5.2). The number of segments is set dynamically by the drive and cannot normally be set by the host (it can
be set using the PM bit as described in Section 4.5.3). The size in Kbytes of each segment is not reported by
the Mode Sense command page 08h, bytes 14 and 15. The value 0XFFFF is always reported. If a size specifi-
cation is sent by the host in a Mode Select command (bytes 14 and 15) no new segment size is set up by the
drive, and if the STRICT bit in Mode page 00h (byte 2, bit 1) is set to one, the drive responds as it does for any
attempt to change unchangeable parameters (see SCSI Interface Product Manual).
4.5.1 Caching write data
Write caching is a write operation by the drive that makes use of a drive buffer storage area where the data to
be written to the medium is stored in one or more segments while the drive performs the write command.
If read caching is enabled (RCD=0), then data written to the medium is retained in the cache to be made avail-
able for future read cache hits. The same buffer space and segmentation is used as set up for read functions.
The buffer segmentation scheme is set up or changed independently, having nothing to do with the state of
RCD. When a write command is issued, if RCD=0, the cache is first checked to see if any logical blocks that
are to be written are already stored in the cache from a previous read or write command. If there are, the
respective cache segments are cleared. The new data is cached for subsequent Read commands.
If the number of write data logical blocks exceeds the size of the segment being written into, when the end of
the segment is reached, the data is written into the beginning of the same cache segment, overwriting the data
that was written there at the beginning of the operation. However, the drive does not overwrite data that has not
yet been written to the medium.