Filter
Top Products
Profoto D4 – Generators
D4D4
Profoto D4 – Generators
Profoto 26 The Light Shaping Company The Light Shaping Company
27 Profoto
is 100% charged to the chosen power level.To change the ready signal mode, hold down or
push repeatedly the
Ready Signal Button [17] until the desired function is visible at the
Ready Signal Indicators [16]:
1. BEEP – a short acoustic signal indicates that the generator is fully charged.
2. BUZZ – an intermitting signal is audible while the generator is charging.
3. BEEP & DIM – the modelling light is dimmed while charging and a short acoustic signal
indicates that the generator is fully charged.
4. BUZZ & DIM – an intermitting signal is audible and the modelling light is dimmed
while charging.
5. DIM – the modelling light is dimmed while charging.
After 5. the functions return to 1.
PLEASE NOTE! To guard against wrong exposures, it is not possible to release a
flash while the generator is charging. If you try, a long beep will indicate that no
flash was released.
Photo/IR-Cell
If the Photo/IR-Cell On/Off Button [6] lights up, the built-in Photocell[5] will sense other
flashes as well as IR-signals from most IR-transmitters. Activate or deactivate the photocell
by pushing the
Photo/IR-Cell On/Off Button [6].
Auxiliary Functions
The D4 series offers advanced functions like “Interval” for stroboscopic effects, “Sequence”
for multi exposures or multi pops to increase the flash output, and “Delay” to create wipe
effects or for pictures of fast moving objects made with an electronic release system.
set the interval time now visible in the Power Display [10] from 0.1-60s. by turning the
Power Dial [13] for outlet A. If you press down the dial while rotating, the interval time
changes in bigger steps.
PLEASE NOTE! The interval function can be activated only if you also use the
sequence function. If the generator can’t deliver the desired interval because of
a longer recharging time, it will release the flashes as fast as possible and an
long beep will indicate the improper use.
B – “S” for Sequence
Activate this function by pushing the corresponding Flash and Modelling Light Button [12]
and set the sequence now visible in the
Power Display [10] from 2-60 flashes by turning
the
Power Dial [13] for outlet B. If you press down the dial while rotating, the sequence
changes in bigger steps.
C – “d” for Delay
Activate this function by pushing the corresponding Flash and Modelling Light Button [12]
and set the delay time now visible in the
Power Display [10] from 0.01-60s. by turning the
Power Dial [13] for outlet C. If you press down the dial while rotating, the delay time
changes in bigger steps.
PLEASE NOTE! Always check the optimal delay time by taking test exposures:
All cameras have a different release delay and the effect depends on the speed
and moving direction of the subject. The following list is a rough basis for your
own tests to create wipe effects:
Wipe effect (Rear Curtain) Sync Time Decimal Equivalent Recommended Delay
1/1 1 second 0.98 seconds
1/2 0.5 seconds 0.49 seconds
1/4 0.25 seconds 0.24 seconds
1/8 0.125 seconds 0.12 seconds
1/15 0.0667 seconds 0.06 seconds
1/30 0.0333 seconds 0.03 seconds
1/60 0.0167 seconds 0.01 seconds
D – “r” for Radio
If the D4 is equipped with a radio slave receiver, you can activate this function by pushing
the corresponding
Flash and Modelling Light Button [12] and set the channel now visible in
By pressing and holding down the Auxiliary Functions Button [7] you enter the auxiliary
mode and the
Power Displays [10] will show the following functions:
A– “I” for Interval
Activate this function by pushing the corresponding Flash and Modelling Light Button [12]and