Filter
Top Products
-- 6 --
runfor30 moreseconds at the OFFCHOKE
position before squeezing and releasing the
throttle trigger to release the throttle lock.
NOTE: If engine dies with the choke lever in
the OFF CHOKE position, move the
choke lever to the HALF CHOKE position
and pull the rope until theengine runs, but
no m ore than 6 pulls.
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Slowly press the primer bulb 6 times.
3. Move the choke lever to the HALF
CHOKE position.
4. Engage the throttle lock as directed in
STARTING A COLD ENG INE.
NOTE: Keep the throttle lock engaged until
the engine starts.
5. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
6. Allow the engine to run 10 seconds, then
move the choke lever to the OFF CHOKE
position.
7. Releasethethrottle lockby squeezingand
releasing the trigger.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not
run, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
theON/OFFswitchintheONpositionandthe
choke lever in the OFF CHOKE position and
engaging the t hrottle lock as directed in the
STARTING A COLD ENGINE section; then,
pull the rope to clear the engine of excess
fuel. Sta rting coul d require pul ling the starter
rope many times depending on how badly the
unit is flooded. If the unit still doesn’t start, refer
to the TROUBLESHOOTING T ABLE or call
1-800-554-6723.
SERVICE
WARNING: Ensure ON/OFF switch
is in the OFF position and disconnect the
spark plug before performing maintenance
except for carburetor adjustments.
HELPFUL TIP
IMPORT ANT: Have all
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed b y an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
GENERAL RECOMMENDATIONS
Thewarranty o nt hisunitdoesnot coveritems
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty , the ope rator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
CHECK FOR DAMA GED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/OF F Switch -- Ensure ON/OF F switch
functions properly by moving the switch tothe
OFF position. Make sure engine stops; then
restart engine and continue.
S Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
S Gearbox -- Do notuse ifthe gearbox shows
signs of damageor leaks. After50 hours of
use, we recommend that your gearbox be
serviced by an authorized service dealer.
INSPECT AND CLEAN UNIT AND
LABELS
S Before and after each use, inspect com-
plete unitfor loose o rdamaged parts. After
each use, clean the unit and labels using a
damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
Air Filter
Cover
Screw
Air Filter
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep debrisfrom fallinginto thecarburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: Donotcleanfilteringasoline orother
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporativeemis-
sions.
3. Wash the filter in soap and water.
4. Allow filter to dry .