Filter
Top Products
5
Symmetrical Guide Bar
Large Radius Tip
S
Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood togradually rideintothe cutter.Low--
Kickback Chain has met kickback per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
Low---Kickback
Chain
Not aLow---Kickback Chain
CanObstruct Material
Contoured Depth Gauge
Elongated Guard Link
Deflects
Kickback Force
And Allows Wood
ToGradually
Ride Into Cutter
S
Front Hand Guard, desi gned to reduce the
chanceof yourleft handcontactingthechain
if your hand slips o f f the fr ont handlebar.
S
Position of front and rear handlebars, de-
signed with distance between handles and
“in-line” with each other. The spread and
“in-line” position o f the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
CHAIN BRAKE AND CKA ANGLE
S
Chain Brake, designed to stop the chain in
the event of kickback.
WARNING:
WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac-
tion which throws the bar and rotating chain
back and up toward the operator. Kickback
can be caused by allowing contact of thebar
tip in the danger zone with any hard object.
Kickback canalsobecaused bypinching the
sawchain along thetopof theguide bar. This
action may push the gui de bar rapidly back
toward the operator. Either of these events
may cause you to lose control of the saw
which could result i n serious injury or even
death. DONOT RELYUPON ANY OFTHE
DEVICES BUILT INTO YOUR SAW. YOU
SHOULDUSE THESAW PROPERLYAND
CAREFULLY TO AVOID KICKBACK. Re-
duced--kickback guide bars and low--kick-
back saw chains reduce the chance and
magnitude of kickback and are recom-
mended. Yoursawhas alow kickback chain
and bar as original equipment. Repairs ona
chain brake should be made by an autho-
rized servicing dealer. Take your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master service dealer.
S
Tipcontact insomecasesmaycause alight-
ning fast reverse REACTION, kicking the
guide bar up and back towar d the operator.
S
Pinching the sawchain along the topofthe
guide bar may push the guide bar rapidly
back toward the operator.
S
Either of these reactions maycause youto
lose control of the saw which could result
in serious injury.Do not rely exclusively
uponthesafetydevices built into yoursaw.
WARNING:
Computed kickback
angle (CKA) listed on your saw and listed in
the CKA table below represents angle of
kickback your bar and chain combinations
will have when tested in accordance with
CSA andANSI standards. Whenpurchasing
replacement bar and chain, considerations
should be given to the lower CKA values.
Lower CKA values represent safer angles to
the user, higher values indicate more angle
and higher kick energies. Computed angles
represented in the non-activated column in-
dicate total energy and angle associated
without activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain brake and resulting kick angle of s aw.
In all cases lower CKA values represent a
safer operating environment for the user.
The following guide bar and chain combina-
tions meet kickback requirements of CSA
Z62.1, Z62.3, & ANSI B175.1 when used on
saws l isted in this manual. Use of bar and
chain combinations other than those listed is
not recommended and may not meet the
CKA requirements per standard.
Computed kickback angle (CKA) Table
BAR
P/N
Length
CHAIN P/N
16!
MODEL
CKA without chain brake
221
530044834 530051480
8
_
NOTE:
If this saw is to be used for commer-
cial logging, a chainbrake isrequired andshall
not be removed or otherwise disabled tocom-
ply with Federal O SHA R egulations for Com-
mercial Logging. Contact your authorized ser-
vice dealer or cal l 1--800--554--6723.
SAFETY NOTICE:
Exposure to vibrations
through prolonged use of gasoline pow ered
hand tools could cause b lood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorder s or
abnormal swellings. Pr olonged use in cold