Filter
Top Products
10
OFF FULL
CHOKE
Choke/
Fast Idle
(SIDE VIEW)
STARTING A WARM ENGINE:
S
MoveON/STOPswitch tothe ONposition.
S
Pull the choke/fast idle lever out to the full
extent, then push the lever back in com-
pletely (to the OFF position).
S
Slowly press the primer bulb 6 times.
S
Pull the starter rope quickly with your right
hand until the engine starts.
S
Squeeze and release throttle trigger, al-
lowing engine to idle.
DIFFICULT STARTING (or s tarting a
flooded engine):
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ON/
STOP switch is in the ON position.
Starting could require pulling the starter rope
handle many times depending on how badly
the unit isflooded. Ifengine fails tostart, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
CHAIN BRAKE
WARNING:
WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac-
tion which throws the bar and rotating chain
back and up toward the operator. Kickback
can be caused byallowing contact of the bar
tip in the danger zone with any hard object.
Kickback canalso becaused bypinching the
sawchain along thetopof theguide bar. This
action may push the guide bar rapidly back
toward the operator. Either of these events
may cause you to lose control of the saw
which could result in serious injury or even
death. DO NOT RELY UPON ANY OFTHE
DEVICES BUILT INTO YOUR SAW. YOU
SHOULD USE THESAW PROPERLYAND
CAREFULLY TO AVOID KICKBACK. Re-
duced--kickback guide bars and low--kick-
back saw chains reduce the chance and
magnitude of kickback and are recom-
mended. Your sawhas alow kickback chain
and bar as original equipment. If the brake
band is worn too thin it may break when the
chain brake istriggered. With abroken brake
band, the chain b rake will not stop the chain.
The chain brake should be replaced by an
authorized service dealer if any part is worn
to less than 1/32” thick. Repairs on a chain
brake should be m ade by an authorized ser-
vice dealer. Takeyour unit tothe place ofpur-
chase if purchased from a servicing deal er,
or to the nearest authorized master service
dealer.
S
This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S
The inertia--activated chain brake is
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S
If the brake is al ready activated, it is
disengaged by pulling the front hand guard
back toward the front handle as far as
possible.
S
When cutting with the s aw,the chain b rake
must be disengaged.
Disengaged
Engaged
Braking function control
CAUTION:
The chain brake must be
checked several times daily. The engine
must berunning when performing this proce-
dure. This isthe only instance when the saw
should be placed on the ground with the en-
gine running.
Place the saw on firm ground. Hold the han-
dles with both hands and apply full throttle.
Activate the chain brake by turning your left
wrist against the hand guard without releas-
ing your grip around the front handle. The
chain should stop immediately.
Inertia activating function control
WARNING:
When performing the
following procedure, the engine must be
turned off.
Hold the chain saw approximately 14” (35
cm)above astump orother wooden surface.
Release your grip on the front handle and
use the weight of the saw to let the top of the
guide bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.
CUTTING METHODS
IMPORTANT POINTS
S
Check chain tension before first use and
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBL Y section.
S
Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials,
etc.
S
Stop t he saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place part s as necessary.
S
Keep thechain outofdirt andsand. Even a
small amount of dirt will quickly dull achain
and thus increase the possibility of kick-
back.
S
Practice cutting afew small logs using the
following techniques to get the “feel” ofus-