Filter
Top Products
DKAX200DLC Litho in U.S.A. (09-05)
200D / LC
Engine
l
Certified to EPA Tier 3 emissions
l Auto-idle system
l Automatic belt tension device
l Batteries (two 12 volt), 440-min. reserve capacity
l Coolant recovery tank
l Dual-element dry-type air filter
l Electronic engine control
l Enclosed fan guard (conforms to SAE J1308)
l Engine coolant to –34°F (–37°C)
l Fuel filter with water separator
l Full-flow oil filter
l Turbocharger with charge air cooler
l Muffler, under hood, with vertical curved end
exhaust stack
l Cool-on-demand hydraulic-driven fan
l 500-hour engine oil-change interval
l 100% (45 deg.) off-level capability
l Engine-oil-sampling valve
s Hydraulic fan reverser
s Engine coolant heater
s Direct-drive fan
Hydraulic System
l
Reduced-drift valve for boom down, arm in
l Auxiliary hydraulic valve section
l Spring-applied, hydraulically released automatic
swing brake
l Auxiliary hydraulic-flow adjustments through
monitor
l Auto power lift
l 5,000-hour hydraulic oil-change interval
l Hydraulic-oil-sampling valve
s Auxiliary hydraulic lines
s Auxiliary pilot and electric controls
s Hydraulic filter restriction indicator kit
s Load-lowering control device
s Single-pedal propel control
s Control pattern-change valve
Undercarriage
l
Planetary drive with axial piston motors
l Propel motor shields
l Spring-applied, hydraulically released automatic
propel brake
l Track guides, front idler and center
l Two-speed propel with automatic shift
l Upper carrier rollers (2)
l Sealed and lubricated track chain
200D / LC
Undercarriage (continued)
s Triple semi-grouser shoes, 24 in. (600 mm)
s Triple semi-grouser shoes, 28 in. (700 mm)
s Triple semi-grouser shoes, 32 in. (800 mm)
Upperstructure
l
Right- and left-hand mirrors
l Vandal locks with ignition key: Cab door / Fuel
cap / Service doors / Toolbox
l Debris-screening side panel
l Remote-mounted engine oil and fuel filters
Front Attachments
l
Centralized lubrication system
l Dirt seals on all bucket pins
l Less boom and arm
l Oil-impregnated bushings
l Reinforced resin thrust plates
l Tungsten carbide thermal coating on arm-to-
bucket joint
s Arm, 7 ft. 11 in. (2.42 m)
s Arm, 9 ft. 7 in. (2.91 m)
s Attachment quick-couplers
s Boom cylinder with plumbing to mainframe for
less boom and arm
s Buckets: Ditching / Heavy duty / Heavy-duty
high capacity / Side cutters and teeth
s Material clamps
s Super-long fronts
Operator’s Station
l
Adjustable independent control positions (levers-
to-seat, seat-to-pedals)
l AM/FM radio
l Auto climate control/air conditioner, 20,000
Btu/hr. (5.9 kW), with heater and pressurizer
l Built-in operator’s manual storage compartment
and manual
l Cell-phone power outlet, 12 volt, 60 watt, 5 amp
l Coat hook
l Deluxe suspension cloth seat with 4-in. (100 mm)
adjustable armrests
l Floor mat
l Front windshield wiper with intermittent speeds
l Gauges (illuminated): Engine coolant / Fuel
l Horn, electric
l Hour meter, electric
l Hydraulic shutoff lever, all controls
l Hydraulic warm-up control
200D / LC
Operator’s Station (continued)
l Interior light
l Large cup holder
l Machine Information Center (MIC)
l Mode selectors (illuminated): Power modes –
three / Travel modes – two with automatic shift /
Work mode – one
l Multifunction, color LCD monitor with: Diagnostic
capability / Multiple-language capabilities / Main-
tenance tracking / Clock / System monitoring
with alarm features: Auto-idle indicator, engine
air cleaner restriction indicator light, engine
check, engine coolant temperature indicator light
with audible alarm, engine oil pressure indicator
light with audible alarm, low-alternator-charge
indicator light, low-fuel indicator light, fault-code
alert indicator, fuel-rate display, wiper-mode
indicator, work-lights-on indicator, and work-
mode indicator
s Monitor system with alarm features: Hydraulic
oil filter restriction indicator light
l Motion alarm with cancel switch (conforms to
SAE J994)
l Power-boost switch on right console lever
l Auxiliary hydraulic control switches in right con-
sole lever
l SAE two-lever control pattern
l Seat belt, 2 in. (51 mm), retractable
s Seat belt, 3 in. (76 mm), non-retractable
l Tinted glass
l Transparent tinted overhead hatch
l Hot/cold beverage compartment
s Air-suspension heated seat
s 24- to 12-volt D.C. radio convertors, 10 amp
s Circulation fan
s Protection screens for cab front, rear, and side
s Window vandal protection covers
Electrical
l
80-amp alternator
l Blade-type multi-fused circuits
l Positive terminal battery covers
s Cab extension wiring harness
l JDLink
TM
Ultimate wireless communication
system with 3 years of service
Lights
l
Work lights: Halogen / One mounted on boom /
One mounted on frame
200D / 200D LC EXCAVATORS
Key: l Standard equipment s Optional equipment *See your John Deere dealer for further information.
CONTROL OWNING AND OPERATING COSTS
Customer Personal Service (CPS) is part of John Deere’s proactive, fix-before-fail strategy on
machine maintenance that will help control costs, increase profits, and reduce stress. Included
in this comprehensive lineup of ongoing programs and services are:
Fluid analysis program – tells you what’s going on inside all of your machine’s major com-
ponents so you’ll know if there’s a problem before you see a decline in performance. Fluid analysis
is included in most extended coverage and preventive-maintenance agreements.
Component life-cycle data – gives you vital information on the projected life span of com-
ponents and lets you make informed decisions on machine maintenance by telling you approxi-
mately how many hours of use you can expect from an engine, transmission, or hydraulic pump.
This information can be used to preempt catastrophic downtime by servicing major components
at about 80 percent of their life cycle.
Preventive Maintenance (PM) agreements – give you a fixed cost for maintaining a machine
for a given period of time. They also help you avoid downtime by ensuring that critical maintenance
work gets done right and on schedule. On-site preventive maintenance service performed where
and when you need it helps protect you from the expense of catastrophic failures and lets you
avoid waste-disposal hassles.
Extended coverage – gives you a fixed cost for machine repairs for a given period of time
so you can effectively manage costs. Whether you work in a severe-service setting or just want
to spread the risk of doing business, this is a great way to custom-fit coverage for your operation.
And an extended coverage contract also travels well because it’s backed by John Deere and is
honored by all Deere construction dealers.
Customer Support Advisors (CSAs) – Deere believes the CSA program lends a personal
quality to Customer Personal Service (CPS). Certified CSAs have the knowledge and skills for
helping make important decisions on machine maintenance and repair. Their mission is to help
you implement a plan that’s right for your business and take the burden of machine maintenance
off your shoulders.
Net engine power is with standard equipment including air
cleaner, exhaust system, alternator, and cooling fan at test
conditions per ISO9249. No derating is required up to 10,000-ft.
(3050 m) altitude.
Specifications and design subject to change without notice. Wherever applicable, specifications are in accordance with SAE stan-
dards. Except where otherwise noted, these specifications are based on units with 9-ft. 7-in. (2.91 m) arms; 42-in. (1065 mm),
1.19-cu. yd. (0.91 m
3
), 1,951-lb. (886 kg) heavy-duty buckets; 10,463-lb. (4750 kg) counterweights; full fuel tanks; and 175-lb.
(79 kg) operators; and a 200D LC unit with 32-in. (800 mm) triple semi-grouser shoes.