Filter
Top Products
44
OPTION AVAILABILITY FOR EACH MODEL
MODEL
OPTIONS
75E 8KM 9W 10Y 11R 13H 14KM 14KC
14KCR
16KM 16BV 18BV 18H 20H
Drivematic Transmission
Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Weight Kit (26 Lbs.) (Note 1)
Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Lift Bail Kit (Note 2)
Y Y Y Y Y Y Y Y Y Y Y Y Y N/A
Tie Down Bracket Kit
Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Water Tank Kit (5 Gal.) (Note 3)
N/A Y Y Y Y Y Y Y Y Y Y Y Y N/A
Outer Flange – 1/2″Cut (Note 4)
N/R N/R
N/R
N/R N/R Y Y Y Y Y Y Y Y Y
Kit, 3/4″ Cut (Note 5)
N/R N/R
N/R
N/R N/R N/R N/R N/R N/R Y Y Y Y Y
Kit, 1″ Cut (Note 5)
N/R N/R
N/R
N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R Y
Electric Water Pump (Note 6)
N/A N/A
N/A
Y N/A N/A N/A Y N/A Y Y Y Y Y
Hourmeter Kit (Note 6)
N/A N/A
N/A
Y N/A N/A N/A Y N/A Y Y Y Y Y
Blade Guard Left / Right Cutting
14″ Blade Guard (Note 7)
L/R L/R
L/R
L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R
18″ Blade Guard (Note 8)
L/R L L L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R
20″ Blade Guard
L L L L/R L/R L/R L L/R L/R L/R L/R L/R L/R L/R
Y = Available N/A = Not Available (Item will NOT work on this model) N/R = Available but Not Recommended
L = This Size Blade Guard Will Fit Only On Left Hand Side Of Saw L/R = This Size Blade Guard Will Fit On Left or Right Side Of Saw
Notes: Warning: See operating instructions and applicable instruction sheets before installation of any of these items!
1. Weight Kit: Standard Equipment for 11R, 13H, 14KC, 16BV, 18BV, 18H, 20H With 18″ Blade Guard (See Note 7 & 8). Installation: See parts list.
2. Lift Bail Kit: Available As Factory Installed (most models). Standard equipment for 75E model because electrical control box is mounted onto lift bail (effective
January 1997). This option must be ordered to use the optional “Water Tank Kit” (See Note 3). See Instruction Sheet 0A7673 for installation instructions.
3. Water Tank Kit: Must order Lift Bail Kit to use water tank kit. Use only with dry cutting blades. Water flow (Approx. 1/2 Gallon Per Minute) is not sufficient for
use with wet cutting diamond blades. N/A for 75E models because electric control box is mounted onto lift bail. Installation: See parts list.
4. Outer Flange 1/2
″
Cutting: Mounts directly to standard bladeshaft. Use Only For Blade Stacking Width Of 7/16″– 1/2″. Use Standard Outer Flange
(P/N 167962) For Blade Stacking Width Of 0 – 3/8″. Available For Use On Right Or Left Side Of Saw.
5. Wide Cutting Kits: Available for all Models. Not recommended for engine sizes less than 16 HP (4 Belt Bladeshaft Drive). Kit Includes A 4 Groove Blade
Shaft Pulley. N/R Engines Require A 3 Groove Bladeshaft Pulley-Order & Install Separately. See Instruction Sheet 0A7767.
6. Electric Water Pump Kit / Hourmeter Kit: Available only on models shown. Engine must have electric starter to power this item. Installation: See parts list.
7. 14
″
Blade Guard: Not Available For Factory Installation--effective January 1997. Available Through Service Parts Only.
8. 18
″
Blade Guard: Standard Equipment--effective January 1997 For All Models except for 20H (20H Model Equipped with a 20″ Blade Guard).