Husqvarna PAC IV-9W Lawn Mower User Manual


 
13
FIGURE 2- Parts List (Items 13 - 72)
(REV 2-12-2007)
DIAG
LOC.
PART
NO.
QTY
REQ
DESCRIPTION
(* Denotes Metric Item)
DIAG
LOC.
PART
NO.
QTY
REQ
DESCRIPTION
(* Denotes Metric Item)
13 164238 1 Clamp (Used On 1994 Models Only)
*42 167943 1 Blade Guard Assy – 14” (Complete)
–– 166673 1 Clamp, Insulated, 5/8” I.D. x 1/4" Hole (14kcr)
*— 195129 1 Blade Guard - Compl – 18” Husq Gray
*— 195140 1 Blade Guard - Compl – 20” Husq Gray
*14 139761 1 Capscrew, Hex Hd., M6 x 1.0 x 20mm
43
502447301
1 Blade Guard, Front – 18” Husq Gray
–– 163688 1 Capscrew, Hex Hd., M6 x 1.0 x 16mm (14kcr)
43
502447701
1 Blade Guard, Front – 20” Husq Gray
*15 139745 1 Locknut, Fiber, M6 x 1.0
139076 1 Front Blade Guard Weldment – 14”
139596 1 Front Blade Guard Weldment – 18” (Note H)
*16 167478 1 Capscrew, Hex Hd., M8 x 1.25 x 25mm
195120 1 Front Blade Guard Weldment – 18” (Note H)
180846 1 Front Blade Guard Weldment – 20” (Note H)
139749 4 Capscrew, Hex Hd., M10 x 1.5 x 25mm (14KCR)
195134 1 Front Blade Guard Weldment – 20” (Note H)
17 020763 2 Washer, Flat, 5/16" SAE
44 ------ -- Rear Blade Guard - Not Available Use Item 42
173014 4 Washer, Flat, M10 (14KCR)
45 139075 1 Hinge (Note H)
*18 139738 1 Locknut, Fiber, M8 x 1.25
45A 195127 1 Hinge (Note H)
139748 4 Locknut, Fiber, M10 x 1.5 (14KCR)
*46 139761 6 Capscrew, Hex Hd, M6 x 1.0 x 20mm (Note H)
*19 139749 3 Capscrew, Hex Hd., M10 x 1.5 x 25mm
*46A 167478 6 Capscrew, Hex Hd M8 x 1.25x25mm (Note H)
*20 173014 3 Washer, Flat, M10
47 020762 6 Washer, Flat, 1/4" SAE (Note H)
*21 139748 3 Locknut, Fiber, M10 x 1.5
*47A 173059 6 Washer, Flat, M8 (Note H)
*22 139749 4 Capscrew, Hex Hd, M10 x 1.5 x 25mm (5E, 75E)
*48 139745 6 Locknut, Fiber, M6 x 1.0 (Note H)
*23 173014 4 Washer, Flat, M10
*48A 139748 7 Locknut, Fiber, M8 x 1.25 (Note H)
*24 139748 4 Locknut, Fiber, M10 x 1.5
49 040275 1 Fitting, 3/8" NPT Male x 3/4" Male
25 167990 1 Motor Base (75E)
50 139045 1 Manifold
177599 1 Engine Base (14KCR)
51 139051 1 Gasket, Manifold
26 167992 2 Spacer, Engine (9W, 14KM, 18H, 20H)
*52 167551 4 Capscrew, Hex Hd, M6 x 1.0 x 40mm
27 020365 2 Capscrew, Hex Hd., 3/8"-16 x 2-1/4"
*53 139745 4 Locknut, Fiber, M6 x 1.0
28 020323 2 Capscrew, Hex Hd.,3/8-16 x 1"(Full Thread)
54 167045 2 Water Tube -14"
29 020377 2 Capscrew, Hex Hd., 3/8"-16 x 1-1/2"
167046 2 Water Tube -18" & 20"
30 167894 1 Blade Shaft-Complete-3 Groove (5 – 14 HP)
55 020864 2 Plug, 1/8" NPT
167893 1 Blade Shaft-Complete-4 Groove (16 – 20 HP)
56 049212 2 Clamp, Water Tube
31 167846 1 Nut, 5/8"-11UNC-LH Thread (Black Finish)
*57 167818 4 Screw, Flat Hd., M6 x 1.0 x 16mm
32 167962 1 Outer Collar w/ Drive Pin
*58 139745 4 Locknut, Fiber, M6 x 1.0
32A 167964 1 Drive Pin, 3/8" Dia x 1-1/8" Long
59 040330 1 Spring
33 167961 1 Blade Shaft w/ Inner Collars *60 167761 2 Capscrew, Hex Hd, M5 x 0.8 x 20mm
33A 167185 2 Inner Collar *61 172011 4 Nut, Standard Hex M5 x 0.8
34 020067 1 Key, 1/4" Sq. x 1-1/4" 62 020782 2 Lockwasher, Split, #10
35 167895 2 Bearing w/Collar & SS (Eccentric Lock) *63 197227 1 Capscrew, Hex Hd M8 x 1.25 x 20mm
*64 020785 1 Lockwasher, Split, M8
36 020540 2 Setscrew, Socket Hd., 1/4"-20 x 1/4"
*37 139752 4 Capscrew, Hex Hd., M10 x 1.5 x 75mm *65 167749 1 Capscrew, Hex Hd, M10 x 1.5 x 90mm
*38 173014 4 Washer, Flat, M10 *66 162004 1 Lockwasher, Split, M10
*39 139748 4 Locknut, Fiber, M10 x 1.5 *67 173014 1 Washer, Flat, M10
68 139255 1 Battery, 12V, 230 CCA – WET
40 139300 1 Pulley, 3G3V3.65-1" w/SS (5 - 14HP ) -- 139255A 1 Battery, 12V, 230 CCA - DRY (Opt.)
167896 1 Pulley, 4GR3V3.65-1" w/SS (16 - 20 HP)
40A 020541 2 Setscrew, Soc. Hd., 1/4"-20x3/8" (For 139300) *69 167786 1 Battery Box Weldment
020541 4 Setscrew, Soc. Hd., 1/4"-20x3/8" (For 167896) 70 167036 1 Strap, Battery Mount (Includes Item70A)
70A 163248 1 Strip, Sponge Rubber (15 inches)
41 167847 1
Nut, 5/8"-11UNC-RH Thread (Gray Finish)
*71 197227 2 Capscrew, Hex Hd, M8 x 1.25 x 20mm
72 020785 2 Lockwasher, Split, 5/16”
See Notes on Page 15