Filter
Top Products
GENERAL SAFETY PRECA
UTIONS
8 – English
• Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool´s operation. If damaged, have the power tool
repaired before use.
Many accidents are caused by
poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Battery tool use and care
• Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
• Use power tools only with specifically designated
battery packs.
Use of any other battery packs may
create a risk of injury and fire.
• When a battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may
cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritations
or burns.
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained.
Chain saw safety warnings
• Keep all parts of the body away from the saw chain
when the chain saw is operating. Before you start
the chain saw, make sure the saw chain is not
contacting anything.
A moment of inattention while
operating chain saws may cause entanglement of you
clothing or body with the saw chain.
• Always hold the chain saw with your right hand on
the rear handle and your left hand on the front
handle.
Holding the chain saw with a reversed hand
configuration increases the risk of personal injury and
should never be done.
• Hold the power tool by insulated gripping surface
only, because the saw chain may contact hidden
wiring or its own cord.
Saw chain contacting a ”live”
wire may make exposed metal parts of the power tool
” live” and could give the operator an electric shock.
• Do not operate a chain saw in a tree. Operation of
chain saw while up a tree may result in personal injury.
• Wear safety glasses and hearing protection.
Further protective equipment for head, hands,
legs and feet is recommended.
Adequate protective
clothing will reduce personal injury by flying debris or
accidental contact with the saw chain.
• Always keep proper footing and operate the chain
saw only when standing on fixed, secure and level
surface.
Slippery or unstable surfaces such as
ladders may cause a loss of balance or control of the
chain saw.
• When cutting a limb that is under tension be alert
for spring back.
When the tension in the wood fibres
is released the spring loaded limb may strike the
operator and/or throw the chain saw out of control.
• Use extreme caution when cutting brush and
saplings.
The slender material may catch the saw
chain and be whipped forward toward you or pull you
off balance.
• Carry the chain saw by the handle with the chain
saw switched off and away from your body. When
transporting or storing the chain saw always fit
the guide bar cover.
Proper handling of the chain
saw will reduce the likelihood of accidental contact
with the moving saw chain.
• Follow the instruction for lubricating, chain
tensioning and changing accessories.
Improperly
tensioned or lubricated saw chain may either brake or
increase the chance of kickback.
• Keep handles dry, clean and free from oil and
grease.
Greasy, oily handles are slippery causing
loss of control.
• Cut wood only. Do not use chain saw for purposes
not intended. For example: do not use chain saw
for cutting plastic, masonry or nonwood building
materials.
Use of the chain saw for operations
different than intendedcould result in a hazardous
situation.
• We strongly recommend that first time users practice
sawing logs on a saw horse or cradle.
Causes and operator prevention of
kickback
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and
pinches the saw chain in the cut. Tip contact in some
cases may cause a sudden reverse reaction, kicking the
guide bar up and back towards the operator. Pinching the
saw chain along the top of the guide bar may push the
guide bar rapidly back towards the operator. Either of
these reactions may cause you to lose control of the saw
which could result in serious personal injury. Do not rely
exclusively upon the safety devises built into your saw. As
a chain saw user, you should take several steps to keep
your cutting jobs free from accident or injury. Kickback is