6
chain brake should be made by an autho-
rized servicing dealer. Take your unit to the
place of purchase if purchased from a
Husqvarna servicing dealer, or to the near-
est authorized Husqvarna service dealer.
S Tip contact in some cases may cause a
lightning fast reverse REACTION, k icking
theguide barupandback t owardtheoper-
ator.
S Pinching thesaw chainalongthetopofthe
guide bar may push the guide bar rapidly
back toward the operator.
S Eitherof thesereactionsmay causeyouto
lose control of the saw which could result
in serious injury. Do not r ely exclusively
uponthesafetydevices builtintoyoursaw.
W ARNING:
Computed kickback
angle (CKA) listed on your saw and listed i n
the CKA table below represents angle of
kickback your bar and chain combinations
will have when tested in accordance with
CSA(CanadianStandardsAssociation) and
ANSI standards. When purchasing replace-
ment bar and chain, considerations should
be given to the lower CKA v alues. Low er
CKA v alues represent safer angles to the
user, higher values indicate more angle and
higher kick energies.Computedangles rep-
resented in the non-activated column indi-
cate total energyand angle associated with-
out activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain break and resulting kick angle of saw.
In all cases lower CKA values represent a
safer operating environment for the user.
The following guide bar and chain combina-
tions meet kickback requirements of C SA
Standards Z62.1, Z62.3, & ANSI B175.1
when used on saws listed in this manual.
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.
Computed kickback angle (CKA) Table
BAR
Type Length CHAIN TYPE
0.050 GA 14
!
91VG/VJ--- 52
MODEL
0.050 GA
16
!
91VG---56
25
_
136
25_
141
141 0.050 GA 18
!
H 30 --- 72
38_
CKA WITHOUT
CHAIN BRAKE
136
0.050 GA
16
!
91VG---56
25
_
NOTE:
If this saw is to be used for
commercial logging, a chain brake is
required and shall not be removed or
otherwise disabled to comply with Federal
OSHA RegulationsforCommercialLogging.
Contact your authorized Husqvarna service
dealer.
SAFETY NOTICE:
Exposure to
vibrations throughprolongeduseof gasoline
powered hand tools could cause blood
vessel or nerve damage in the fingers,
hands, and joints of people prone to
circulation disorders or abnormal swellings.
Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If s ymptoms occur such as
numbness, pain, l oss of strength, change in
skin color or texture, or loss of feeling in the
fingers, hands, orjoints, discontinue the use
of this tool and seek medical attention. An
anti-vibrationsystem doesnotguaranteethe
avoidance of these problems. Users who
operate power tools on a continual and
regular basis must monitor closely their
physical condition and the condition of this
tool.
SPECIALNOTICE:
Yoursawisequipped
with a temperaturelimiting muffler andspark
arresting screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require
many internal combustion engines to be
equipped with a spark arrestor screen by
law. If you operatea chain saw in a state or
locale wheresuch regulations exist, y ouare
legally responsible for maintaining the
operatingcondition ofthese parts. Failureto
do so is a violation of the law. Refer to the
SERVICEANDADJUSTMENTS s ectionfor
maintenance of the Spark Arresting Screen.
Failure to follow all Safety Rules and
Precautions can result in serious injury. If
situations occurwhicharenotcoveredin t his
manual,usecareandgoodjudgement.Ifyou
need assistance, contact your authorized
service dealer.
STANDARDS
CSA Z62.1 “Chain Saws -- Occupational
Health and Safety”
CSA Z62.3 “Chain Saw Kickback Occupa-
tional Health and Safety ”
ANSI B175.1--2000 -- “American National
Standard for Powered Tools -- Gasoline
Powered Chain Saw -- Safety Require-
ments”