Filter
Top Products
Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed? See
‘To Start your Lawnrake’
2. Is the Power Turned On?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity
supply and consult your local approved Service
Centre.
Poor Collection
1. Disconnect from the mains electricity supply.
2. Clean the outside of the air intakes, the discharge
chute and the underside of the deck.
3. Try a different height of rake. See ‘Height Adjustment’.
4. Check condition of the Tines and replace if necessary.
See ‘Removing and Fitting the Tines’.
5. If poor collection persists.
Immediately disconnect from the mains electricity
supply and consult your local approved Service
Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the tines are functioning correctly.
3. Replace tines if necessary
4. If vibration persists?
Immediately disconnect from the mains electricity
supply and consult your local approved Service
Centre.
Lawnrake becomes heavy to push
1. Disconnect from the mains electricity supply.
2. In long grass or uneven ground, the height of cut
should be raised to a higher position. See Cutting
Height Adjustment.
3. Check that the wheels can rotate freely.
4. If problem persists?
Immediately disconnect from the mains electricity
supply and consult your local approved Service
Centre.
Caring for your Product
Cleaning (T)
• USEGLOVES
• IMPORTANT
It is very important that you keep your product clean.
Grass clippings left in any of the air intakes or under
the deck could become a potential fire hazard.
1. Remove grass from under the deck with a brush.
2. Using a soft brush - remove grass clippings from all
air intakes, the collection box and the vision window
3. Wipe over the surface of your product with a dry
cloth.
• IMPORTANT
Never use water for cleaning your product. Do not
clean with chemicals, including petrol, or solvents -
some can destroy critical plastic parts.
At the End of the cutting Season
1. Replace tines, bolts, nuts or screws, if necessary.
2. Clean your product thoroughly.
3. Make sure that the electric cable is coiled properly.
Storing your product: Store in a dry place where your
product is protected from damage
T
Service Recommendations
1. We strongly recommend that your product is serviced
at least every twelve months, more often in a profes-
sional application.
2. Always use genuine Spare Parts.
3. Prepacked spares are available from most Husqvarna
Outdoor Products stockists and www.flymo.com.
4. Your product is uniquely identified by a silver and black
product rating label
5. If you have a problem with your machine contact your
local Approved Service Centre ensuring you have full
details of your product as described on the product rat-
ing label.
6. Should it be necessary for work to be carried out by your
Service Centre, it is important to take your complete
machine including cable and any extension cables used.
Anetwork of specialist dealers can be found in your local
Yellow Pages.
To obtain service on your product simply telephone or visit
your local Service Centre.
Should you require service under the terms of our guarantee
the Service Centre will require proof of purchase.
All of the centres listed stock genuine Spare Parts.
NOTE: Our Service Repairers act on their own behalf and
are not empowered to commit or legally bind Husqvarna
Outdoor Products in any manner whatsoever.
Environmental Information
Husqvarna Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where
practical, components manufactured in the most environmentally responsible manner, according to company procedures,
and with the potential for recycling at the end of the products’ life.
• Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered when disposing of ‘end-of-life’product.
• If necessary, contact your local authority for disposal information.