Filter
Top Products
9
(GB ) MAINTENANCE
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty
manufacture within one year of original purchase,
Flymo/Partner, through its Authorised Service Repairers will
effect the repair or replacement to the customer free of
charge providing:
(a) The fault is reported directly to the Authorised
Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and
tear.
(e) The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised
by Flymo/Partner.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used outside of the country
for which it was specified.
(i) The machine has not been used commercially.
* This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this
Operator's Manual and understand how to operate and
maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in
accordance with the instructions and
recommendations contained in this Operator's Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular
maintenance and are, therefore not normally subject to
a valid warranty claim: Nylon Line, Electric Mains
cable.
* Caution!
Flymo/Partner does not accept liability under the
warranty for defects caused in whole or part, directly
or indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or
approved by Flymo/Partner, or by the machine having
been modified in any way
Guarantee, Fault Finding Hints, Service Recommendations &
Certificate of Conformity
I, the undersigned P. Howells of
Flymo/Partner, a Division of Electrolux
Outdoor Products Limited, Aycliffe
Industrial Estate, NEWTON AYCLIFFE,
Co. Durham. DL5 6UP. Certify that a
sample of the above product has been
tested and found to comply with
directives:-
89/392/EEC, 89/336/EEC, 73/23/EEC
Signed at
NEWTON
AYCLIFFE..................................................
1998
I, the undersigned P. Howells of
Flymo/Partner, a Division of Electrolux
Outdoor Products Limited, Aycliffe
Industrial Estate, NEWTON AYCLIFFE,
Co. Durham. DL5 6UP. Certify that a
sample of the above product has been
tested using directive 81/1051/EEC as a
guide. The maximum A-weighted sound
pressure level recorded at operator
position under free field semi anechoic
chamber conditions was :-
Signed at
NEWTON
AYCLIFFE...................................................
1998
I, the undersigned P. Howells of
Flymo/Partner, a Division of Electrolux
Outdoor Products Limited, Aycliffe
Industrial Estate, NEWTON AYCLIFFE, Co.
Durham. DL5 6UP. Certify that a sample
of the above product has been tested
using ISO 5349 as a guide. The maximum
weighted root mean square value of
vibration recorded at operator’s hand
position was:-
Signed at
NEWTON
AYCLIFFE.................................................
1998
Fault Finding Hints
1. Line too short
Manually feed out the line.
2. Line broken inside cutting head
Remove cap and re-thread line.
3. Line jammed on spool
Remove cap and spool and rewind line to remove crossed
loops.
4. Excess line feed
Battery needs to be charged.
5. Poor performance
Ensure inside of cutting head housing is clean and free from
debris.
6. Trimmer stops during use
Release switch lever and wait 30 seconds before re-starting.
Service Recommendations
To ensure the maximum life and reliability from your Flymo product
we recommend that it is serviced regularly by an approved
Flymo/Partner Service Centre/Dealer. They have the equipment
facilities and trained personnel to advise you on the service
requirements of your machine. Depending on the machine's use
they will recommend one of the various types of service which are
designed to ensure the maximum economic service life of your
machine.
Certificate of Conformity
Type
Identification of Series
Level
MCT-250
See Product Rating
Label
77.2 dB(A)
Type
Identification of Series
Value
MCT-250
See Product Rating
Label
1.6 m/s
2