Craftsman 358.797922 Blower User Manual


 
l
' _ ' ........ ,.... .................... ._ _ . I . L I!ul ........... In roll.... I,,,,,,
I ASSEMBLY
A.PREPARAT ON
Your Operator's Manual has been developed to help
you assemble the unit and to understand its safe opera_;-
fion._ It is importer that you read your mauual com-
pletely to become familiar with the unit befvre you be_
' gin assemb_. Blower
L READ YOUR OPE_ATOR'S MANUAL
2. The only tool required is astandard screwdriver.
To ease assembly, lubricate locking tabs before
assembling tubes.
Locking _
Bo BLOWER TUBE ASSEMBLY
L Locate the two lockingtabs on the side ofthe bIower
tube. Figure 1.
2.Alignthegrooveson thefiozzlewiththe locking
tabson the blower tube and push the nozzle onto
the blower tube.
3. Turn the noz_e dock-wise untiI the parts snap into
.phce and arefirmlytightened. , .
4. _Mign Grooves on ttIe Blower Tube with I.ec_g
mower 1,met) dp h
e BlowerTube into the Blower Outlet.
5. Turn the Blower Tube clockwise until the parts
snap into placeand arefirmlytightened.
C.VACUUM BAG ASSEMBLY
1...Open'thezipperonthelarge'endofthevacuum bag.
2. InserttheElbowTube, groovedend first,through
the zipper openiag in the va__um beg _ 2).
Then, push the grooved _ of the Elbow Tube
through the bagtube openingin theother end ofthe
bag.Figures2 &3. Makesurethebegtubeopening
_sflushagain_thetubeflauge. Figure&
"3..Closethe zipper on theb_t_ Make sure the zipper is
.!:,:_dosedcompletely and the zipper seam is tucked to-
.:.'wa.'_l.theinside of the beg. Figure 4 (inset).
D.VACWJUM TUBE ASSFAdBLY
t " 'Aw,crnm ............... I
i Stop.the engine before opening thevaeuum inlet !
| debt or _em_ =_g _ _er_ _ _ the vacu-i
l 'ramtubes. The engine must be st_pped and the Im-I
| p e!!@r,blades no longer tur-aing to avoid serious]
'I_-a.ry fromthe _ta_t_ bhde_ ............ I
1. Remove the blowertubefromthe engine. Figure 4,
2. Settheunit_Mower outletup,on aflatsurface (Fig-
ura 5).Open thevacuum iv-letcoverasfollows:
_u Insertascrewdrivei"int_latcharea._gu:re5.
=b..Gently twist the tip ofthe screwdriver and open
l;he _m_um inlet cover with your other hand.
_; -Holdopenvacuum inlet.coverandalignthe _es
on, the upper vacuum tu_e with the I_:_f_:,_'_m -
s_de the vacuum inlet, Figure 6. Insert the upper
" . rac:m_minto the vacuum inlet; twLstthe upper vac-
uum tube clockwise until parts snap together.
4, Assemble the vacuum tubes by aligning the danted
end of the lower vacuum tube with the blower outlet
as shown in Figure 6. Push the two tubes together
'_ower'vacuum:tube is
::_cu.t:at an angle. Make sure slanted end of vacuum
'__ •'_:.__:'_.b_e_se_ignedwlth bloweroutlet.Figure 6.
,'°..._igure 5
-5-
,t,