Filter
Top Products
Cabela’s
®
Gun Dog
®
— Owner’s Manual
7
Cabela’s
®
Gun Dog
®
— Owner’s Manual
6
USING THE TRANSMITTER
Turning ON the Transmitter
Power up the Transmitter by pressing any
button. You will see the display turn on
when you press any button.
Reset All Programmable Settings
Press and at the same time to
reset all programmable settings to the
default settings. The Transmitter Display
shows all symbols for two seconds during
reset.
Transmitter Default Settings
GS-6001 Defaults
Dog 1&2 Primary Stim Level: 5
GS-7001 Defaults
Dog 1&2 Stim Type: Stim without Tone
Dog 1&2 Primary Stim Level: 7
Dog 1&2 Alt Stim Level: 14
Set Stim Button Intensity Level
To change the intensity level for the Stim
button:
Press or until the desired
stimulation level is displayed. When the
Stim button is pressed, the Receiver will
deliver a stimulation at this setting.
GS-7001 ONLY:
Programming Mode
To enter Programming Mode, press and
hold the Prog/Loc button until the PROG
symbol displays, then release the button.
The Transmitter is now in Programming
mode.
To exit Programming Mode, press and
release the Prog/Loc button again. The
PROG symbol no longer displays.
GS-7001 ONLY:
Program the Stim Type (Tone Option)
For GS-7001 Transmitters, stimulation
may be delivered with or without a tone.
The Transmitter’s default setting is Stim
without Tone.
To choose:
1.Choose desired dog. Press
(Dog Select button).
2.Press the Prog/Loc button until the
PROG symbol shows in the Transmitter
display. Release Prog/Loc button.
3.Press and release TONE. If
you keep pressing the TONE
button, the selection
switches between these choices:
• Stim without Tone (
no Tone symbol
displayed)
• Stim with Tone (Tone symbol displayed)
4.Press and release the Prog/Loc
button to save setting and exit.
For additional information regarding using
the Tone, see Training Tone Option on
page 14.
GS-7001 ONLY:
Set Dual Dog mode
In Dual Dog mode, the continuous
stimulation button (red) controls Dog 1
Collar Receiver, and the Momentary
Stimulation button (gray) controls Dog 2
Collar Receiver. You control two dogs
without using the Dog Select button to
switch between dogs. In this mode, Stim
type is stim without tone.
Explaining the Transmitter Keypad
Buttons (continued)
Prog/Loc (GS-7001 only) – Pressing and
holding this dual-function button until the
PROG symbol appears in the display puts
the Transmitter in programming mode.
Briefly pressing this button starts or stops
Locate Mode (explained on page 10).
Locate (GS-6001 only) – Press this
button to start or stop Locate mode
(explained on page 10).
Transmitter Display Symbols:
The display stays on for 30 minutes after
a button press. After 30 minutes with no
button presses, the display shuts off.
Pressing any button will make the display
turn back on.
Various symbols you might see in the
Transmitter display are explained as
follows:
(Numeric readout) – Appears in
the middle of the display, this shows the
chosen stimulation level. Adjust with the
Stim level up / Stim level down (arrow)
buttons.
–
The left symbol displays
when the Transmitter is controlling Dog
Collar Receiver 1. You can purchase a
second collar to expand the system for
training two dogs. The right symbol
displays when controlling Dog Collar
Receiver 2. Switch between Collar
Receivers by pressing the Dog Select
button. Both symbols display when in
Dual Dog mode. (See Set Dual Dog mode
on page 7.)
– This symbol appears whenever
Tone is part of the Stimulation type
chosen. (See Program the Stim Type on
page 7.)
GS-7001 ONLY:
– This symbol appears when
the Transmitter is in programming mode.
(See Programming Mode on page 7.)
– This symbol appears when
the Transmitter is in Locate mode.
– The battery indicator
provides constant awareness of your
battery’s power level. (See Battery
Indicator on page 9.)
Backlight – The Transmitter features a
backlit display. The display backlight
stays on for 5 seconds after a button
press.
400-1139-1.qxp:two column layout for print 9/25/09 4:03 PM Page 6