Filter
Top Products
Part No. 890604 Form No. F021602C
Page 12 of 12
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
servicing dealer.
22.1
22
BILLY GOAT INDUSTRIES INC.
1803 S.W. Jefferson Street Lee's Summit, MO 64082 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model
& Serial number that are printed on the Billy Goat Serial Plate.
Purchased
from
Purchase
Date
21
Serial Plate
Record your machine model, serial number and
date-of-purchase and where purchased
min
-1
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
Engine stalls or labors when
chipping.
Feeding branches into chipper too rapidly. Engine service may be
required.
Feed branches at a slower rate. Service engine.
Poor chipping performance.
Extremely hard wood. Dull or damaged chipper blade.
Avoid extremely hard wood. Sharpen or replace chipper blade (see
page 8).
Will not vacuum or has poor
vacuum performance.
Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
Solution
Problem Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Engine will not start.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Self propelled drive will not
release.
Clutch cable out of adjustment. Idler return spring disconnected or
broken. Belt is rubbing on chain guard
Adjust clutch cable. Replace return spring. Remount chain guard
No self propelling.
Clutch cable out of adjustment. Worn or broken belt. Worn or broken
clutch cable.
Adjust clutch cable. Replace belt. Replace clutch cable. Replace any
worn or damaged or malfunctioning parts.
Throttle in off position. Out of gasoline. Bad or old gasoline. Spark
Plug wire disconnected. Dirty air cleaner.
Abnormal vibration.
Loose or out of balance impeller or loose engine.
Check impeller and replace if required. Check Engine.
Engine is locked, will not
pull over.
Debris locked in chipper blade, hopper or inside impeller. Engine
problem.
See page 5, Clearing a clogged chipper hopper. Contact an engine
servicing dealer for engine problems.
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
20
19
( Continued from
page 11 )
PARTS LIST
* Denotes
standard
hardware
item that
may be
purchased
locally.
Item
No.
Description
KD512SP
Part No.
Qty.
TKD512SP
Part No.
Qty.
86 Wheel With Sprocket Ass'y Cast ( 21, 94, 95, 96) 890242 2 890242 2
87 Chain 52 Pitch 890239 2 890239 2
88 Belt 4L220 890586 1 890586 1
89 Washer Flat 5/16 (3/8 ID x 7/8 x 1 1/6) *8171003 4 *8171003 4
90 Bolt Carriage 5/16 - 18 x 3/4 *8024039 4 *8024039 4
91 Washer
S
pring Lock 5
/
16 *8177011 4 *8177011 4
92 Nut Regular 5/16 - 18 *8142002 4 *8142002 4
93 Jackshaft 900320 1 900320 1
94 Sprocket (per Assemby) (size # 65A26) 26 Teeth 890238 1 890238 1
95 Screw Self Tap 1/4-14 x 3/4 (Per Assembly) 800505 5 800505 5
96 Washer Lock External Tooth (Per Assembly) *8181007 5 *8181007 5
97 Jackshaft Ass'y (incl. 93, 101, 102, 107, 108, 109) 890197 1 890197 1
98 Shield Muffler TKDSP 890190 1 890190 1
99 Label Clutch 830503 1 830503 1
100
101 Bearin
g
Plate 900317 2 900317 2
102 Bearin
g
Ball
(
with
S
nap Rin
g)
900321 2 900321 2
103
104 Rod Bail Clutch 900970 1 900970 1
105
106
107 Pulley 3"OD x 5/8 Bore 890583 1 890583 1
108
S
procket - 8 Tooth 900302 2 900302 2
109 Roll Pin 3/16 Dia. x 1 1/4 L
g
. *8195166 4 *8195166 4
110 Locknut 5/16 - 18 Flan
g
e 850164 5 850164 5
111
S
crew
C
ap 1
/
4-20 x 1-1
/
2 Hex 8041008 2
112 Bracket Clutch KDSP 890580 1 890580 1
113 Sprin
g
Tension 400217 1 400217 1
114 Bolt Idler 800888 1 800888 1
115 Bolt Shoulder 3/8" x 1/2" 830528 1 830528 1
116 Screw Cap 1/4 - 20 x 1" Lg. *8041006 1 *8041006 1
117 Arm Idler Wa KDSP 890582 1 890582 1
118 Guard Chain Ass'y TKDSP 890600 1 890602 1
119 Nut Lock 5/16-18 Thin *8161041 1 *8161041 1
120 Pulley Idler 1.13"OD x 3/8" Bore 890585 1 890585 1
121
122 Nut Lock 3/8-16 Thin *8161042 1 *8161042 1
123 L
a
b
e
l
R
ea
d
O
wner
'
s
M
anua
l
890301
1
890301
1
R
112 dB