Filter
Top Products
7
BRAKE / TRACTION ADJUSMENTBRAKE / TRACTION ADJUSMENT
BRAKE / TRACTION ADJUSMENTBRAKE / TRACTION ADJUSMENT
BRAKE / TRACTION ADJUSMENT
1. Disconnect the brake linkage from the brake band
arm.
2. With the mower in gear, place the traction levers in the
drive position. Firmly pull back on the handles until the
tires slide to seat the wheel drive belts into the pulleys.
3. Measure the clearance between the bottom of the
traction lever rod and the bottom of the thumb latch slot.
It should be between 3/16" to 1/4", but not exceeding 1/
4". See Figure # 3
4. If the clearance is less than 3/16", disconnect the
traction rod from the traction lever by removing the
hairpin cotter.
5. Adjust the traction rod to the proper clearance by
screwing it out of the swivel if clearance is less than 3 /
16".
NOTE:NOTE:
NOTE:NOTE:
NOTE:
More or less brake pressure may be desired depending
on the operator or conditions of operation. To increase
pressure tighten the wing nut on the brake linkage.
1. Remove front deck belt shield.
2. Loosen whiz nut on turnbuckle.
3. Set belt tension when engagement lever is in the
engaged position.
4. To increase belt tension rotate turnbuckle toward the
rear of the mower until desired tension is gained. Do not
over tighten belts, to much tension will reduce belt and
spindle bearing life. See figure # 6
SETUP AND ADJUSTMENTS FORSETUP AND ADJUSTMENTS FOR
SETUP AND ADJUSTMENTS FORSETUP AND ADJUSTMENTS FOR
SETUP AND ADJUSTMENTS FOR
YAZOO/KEES KUTTER 32", 36" AND 48" COMMERCIAL MOWERSYAZOO/KEES KUTTER 32", 36" AND 48" COMMERCIAL MOWERS
YAZOO/KEES KUTTER 32", 36" AND 48" COMMERCIAL MOWERSYAZOO/KEES KUTTER 32", 36" AND 48" COMMERCIAL MOWERS
YAZOO/KEES KUTTER 32", 36" AND 48" COMMERCIAL MOWERS
HANDLE
TRACTION
LEVER
THUMB LATCH
3/16" to 1/4" CLEARANCE
O.P. LEVER
OPERATOR PRESENCE SWITCH ADJUSTMENTOPERATOR PRESENCE SWITCH ADJUSTMENT
OPERATOR PRESENCE SWITCH ADJUSTMENTOPERATOR PRESENCE SWITCH ADJUSTMENT
OPERATOR PRESENCE SWITCH ADJUSTMENT
The operator presence switches can be adjusted by
loosening the screws on the side of the O.P. lever
linkage and sliding the switch up or down. The O.P.
switch should have a 1/32" to 1/16" gap between the
plunger and the bottom side of the control panel when
operator presence levers are released.
BLADE SWITCH ADJUSTMENTBLADE SWITCH ADJUSTMENT
BLADE SWITCH ADJUSTMENTBLADE SWITCH ADJUSTMENT
BLADE SWITCH ADJUSTMENT
The blade engagement switch can be adjusted by
loosening the screws on the flange under the control
panel and moving the switch in or out. The blade switch
should be adjusted so the plunger is fully depressed
when the engagement lever is fully disengaged.
ADJUSTMENTS - DRIVE BELTSADJUSTMENTS - DRIVE BELTS
ADJUSTMENTS - DRIVE BELTSADJUSTMENTS - DRIVE BELTS
ADJUSTMENTS - DRIVE BELTS
For all drive belts, tension should be set so that belt
vibration is minimized or eliminated when belts are
moving during normal operation. A properly tensioned
belt should have 1/4" to 3/8" deflection at the center of
belt span between pulleys when blades are engaged.
Blade drive belt tension is pre-set at the factory.
NOTE:NOTE:
NOTE:NOTE:
NOTE:
DO NOT over tighten belt. Excessive tension will
decrease belt and spindle bearing life.
BLADE DRIVE BELT ADJUSTMENTSBLADE DRIVE BELT ADJUSTMENTS
BLADE DRIVE BELT ADJUSTMENTSBLADE DRIVE BELT ADJUSTMENTS
BLADE DRIVE BELT ADJUSTMENTS
WARNINGWARNING
WARNINGWARNING
WARNING
BEFORE PERFORMING ADJUSTMENTS ONBEFORE PERFORMING ADJUSTMENTS ON
BEFORE PERFORMING ADJUSTMENTS ONBEFORE PERFORMING ADJUSTMENTS ON
BEFORE PERFORMING ADJUSTMENTS ON
BLADE BELT, TURN MOWER OFF, CLOSE FUELBLADE BELT, TURN MOWER OFF, CLOSE FUEL
BLADE BELT, TURN MOWER OFF, CLOSE FUELBLADE BELT, TURN MOWER OFF, CLOSE FUEL
BLADE BELT, TURN MOWER OFF, CLOSE FUEL
VALVE, AND DISCONNECT SPARK PLUG WIRE.VALVE, AND DISCONNECT SPARK PLUG WIRE.
VALVE, AND DISCONNECT SPARK PLUG WIRE.VALVE, AND DISCONNECT SPARK PLUG WIRE.
VALVE, AND DISCONNECT SPARK PLUG WIRE.
AUXILIARY BLADE DRIVE BELTAUXILIARY BLADE DRIVE BELT
AUXILIARY BLADE DRIVE BELTAUXILIARY BLADE DRIVE BELT
AUXILIARY BLADE DRIVE BELT
(48" MODELS ONLY)(48" MODELS ONLY)
(48" MODELS ONLY)(48" MODELS ONLY)
(48" MODELS ONLY)
To adjust tension of the auxiliary belt rotate nut on
linkage that is attached to deck strap located on the right
side of cutter deck.
Figure 3