Filter
Top Products
3
36
DAILY CHECKLIST
h Check that cutter is properly and securely attached
to tractor.
h During inspection, check that all nuts and bolts are
secure and that all safety shields are in place.
h It is very important that the blade carrier nut and
blade bolts are checked and tightened frequently.
h Check condition of blades and security of attach-
ment.
h Check that PTO driveline shields are securely
locked and clears the front of the cutter frame.
h Adjust the tractor top link so the front of the cutter is
slightly above the rear. Then raise the tractor lift very
slowly, making sure that the front drive shaft shield
does not hit the front of the cutter. If it does, damage
will be done to the drive shaft shield and, if it hits
hard enough, it will also damage the drive shaft
itself. (See page 20.)
NOTE: This type of damage is not covered
under warranty, as it is totally under the control
and the responsibility of the operator.
DELIVERY CHECKLIST
Inspect the cutter thoroughly after assembly to be certain
it is set up properly. The following checklist is a reminder
of points to inspect. Check off each item as it is found
satisfactory or after proper adjustment is made.
h Check operator's manual and familiarize the opera-
tor with all sections of it.
h Check that all safety shielding is in place.
h Check all bolts to be sure they are tight or adjusted
properly at hinged locations.
h Check that all cotter pins are properly installed.
h Check PTO driveline. Make sure it is the correct
length to operate cutter with intended tractor.
h Check that all lubrication points with grease fittings
have been lubricated.
h Check that blades have been properly installed.
Check all blade beam bolts.
h Check cutter attitude, after mounting on tractor.
h Check that gearbox is properly serviced and seals
are not leaking.
h Check shear bolt for proper grade and installation.
h Check front of input gearbox shaft and make sure
that snap ring is properly installed.
h All safety signs (decals) in place and readable.
h When the cutter is transported on a road or highway
at night or during the day, safety devices should be
used for adequate warning to operators of other
vehicles.
CHECKLISTS
IMPORTANT!
Gearbox was not filled at factory. It
must be serviced before operating.
Fill to proper level with SAE 90 oil.
Failure to service will result in
damage to gearbox.
COMER GEARBOX - LF 135.802
PA RTS LIST
(4’ CUTTER)
REF. WORKSAVER COMER NO.
NO. PART NO. PART NO. DESCRIPTION REQ'D.
1 650553 0.135.5000.00 Gear Z23 M5 1
2 650442 0.135.0301.00 Casing 1
3 650554 0.135.2000.00 Shaft 1
4 650555 0.135.6001.00 Pinion Shaft Z12 M5 1
5 650556 0.135.7101.00 Spacer 1
6 650446 0.135.1301.00 Cover 1
7 650447 1.135.7100.00 Protective Washer 1
8 650448 8.0.1.00034 Bearing 6205 1
9 171017 8.0.1.00870 Bearing 6207 1
10 650449 8.0.1.00871 Bearing 6208 2
11 650451 8.2.2.00515 Castle Nut M24 x 2 PR80 B 1
12 650452 8.3.2.00409 Bolt Washer 25 x 44 x 4 1
13 650453 8.4.1.00993 Parallel Key B 10 x 8 x 30 1
14 650557 8.5.1.00029 Snap Ring 40 UNI 7435 1
15 650456 8.5.2.00030 Snap Ring 80 UNI 7437 1
16 650457 8.5.3.00955 Snap Ring SB 81 1
17 650458 8.5.3.01057 Snap Ring SB 125 1
18 650459 8.6.6.00201 Plug
3
/
8
” Gas 2
19 650558 8.7.1.01171 Double Lip Seal 40 x 80 x 12 1
20 650559 8.7.3.01172 Double Lip Seal 35 x 52 x 7 1
21 650463 8.7.6.01058 O-Ring OR-4462 1
22 171007 0.244.7500.00 Shim 51.5 1
23 650454 0.100.7500.00 Shim 35.3 1
24 171014 0.259.7500.00 Shim 48.0 1
25 709059 8.5.1.00680 Snap Ring 40 UNI 7436 1
26 650468 8.4.7.00516 Cotter Pin B5 x 50 1