Filter
Top Products
Parts 17
29929 (Rev. 3/28/2008)
59CL-4 & 59CLF-4 MAIN ASSEMBLY
NOTE: Mower frames sold after 1976 the front side of mower is formed down. Before they had a bolt-on front shield.
Key For Number Used Columns
A Serial Number 100 through 306 (59CL-1) C Serial Number 479 through 822 (59CL-3 & 59CLF-3)
B Serial Number 307 through 478 (59CL-2) D Serial Number 823 and up (59CL-4 & 59CLF-4)
REF PART A B C D DESCRIPTION
1 9700 1 1 1 1 Frame shipping unit
2 4141 1 1 1 1 Right side skid
3 5818 1 1 1 1 Front shield (prior to 1975)
4 25506 1 1 1 1 Right belt shield
5 4176 1 1 1 1 Upper attachment arm
6 484 1 1 1 1 5/8 x 1 x 7/16 HT Sleeve
7 4174 1 1 1 1 Chain attachment bracket
8 4153 2 2 2 2 3/8 NC x 5 Open eyebolt
9 4215 - 2 2 2 2/0 Straight link chain 10-link
10 18336 - - - 2 Caplug, 1-1/16 - 121D SAE
thread -or-
10 4155 2 2 2 2 1/4 Cold shut repair link (not
shown)(on earlier models)
11 ----- ** ** ** 1 Pair of casters
(see page 20 )
21 25557 - - - 1 Center belt shield bracket
22 25555 - - - 1 Center belt shield -or-
22 4130 1 1 1 1 Center shield (for mowers
prior to mid 1975)
23 25507 1 1 1 1 Left belt shield
24 4142 1 1 1 1 Left side skid
25 25513 1 1 1 1 Left side shield
26 ----- - - 1 1 Channel brace
27 ----- 1 1 1 1 Frame angle
28 2688 * 4 4 6 6 1/8 Safety pin
29 4097 4 4 4 4 5/8 x 1-1/2 Clevis pin
29A 410 2 2 2 2 5/8 x 1-3/4 Clevis pin
30 4145 2 2 2 - Rear shield
31 13870 - - 1 1 Right vertical push arm
31A ----- 2 2 - - Attachment arm
32 3369 - - 1 1 Rt attach place (CLF only)
33 13314 - - 2 2 Push channel with clevis bar
33B 4160 2 2 - - Adjustment arm
34 3504 - - 1 1 1/2 x 5/8 x 1-1/16 Sleeve HT
35 13313 - - 1 1 Crosswise rear support
35A 4165 1 1 - - Offset pipe frame
35B 4159 1 1 - - Guide rod
35C 1791 - 6 - - 5/8 x 1 x 9/16 HT Sleeve (for
raising fast-hitch)
35D 4156 1 1 - - 3/8 U-Bolt
36 5655 * 2 2 2 2 5/8 NC x 3-1/2 Carriage bolt
37 3510 - - 1 1 Upper idler bracket
38 3506 - - 1 1 Lower idler bracket
39 3368 - - 1 1 Left attach plate (CLF only)
40 13871 - - 1 1 Left vertical push arm
41 3493 - - 1 1 PTO Sheave, 1BK 6.1H
41A 1505 1 1 - - PTO Sheave, 1BK 7.4H
42 1506 1 1 1 1 10-Spline bushing with bolts
43 3501 - - 1 1 Rear V-belt shield
44 3492 - - 1 1 W172 V-Belt, special -or-
44 4152 1 1 - - W180 V-Belt, special
45A 4336 2 2 2 2 V-Groove idler w/ bearing, rt
45B 6095 2 2 2 2 .626 ID x 1.85 OD Ball
bearing
45C 4335 2 2 2 2 4.50 OD V-Groove idler
sheave less bearing, right
46 4227 3 3 3 3 H3/4 Strt bushing w/ bolts
47 3885 * 3 3 3 3 3/16 x 3/16 x 1-1/4 Key
48 4226 2 2 2 2 1 BK 3.9H Sheave
49 6126 1 1 1 1 3 BK 3.9PD H Sheave
51 ----- 3 3 3 3 Spindle & blades (see
page 19)
53 5753 † - - - 1 Complete decal set
54 25512 † - - - 1 Right side shield with baffle
55 25508 † - - - 1 Front corner baffle
56 25532 † - - - 1 Center baffle rear mtg angle
57 25509 † - - - 1 Center baffle
58 25531 † - - - 1 Center baffle frt mtg lug
59 26516 † - - - 2 Front toe guard with safety
60 26520 † - - - 1 Side discharge chute
61 52310 † 1 1 1 1 French safety decal set
67 24597 * - - - 6 3/8NC x 3/4 Carriage bolt
68 6697 * - - - 2 3/8 NC x 1 Carriage bolt
69 14350 * - - - 12 3/8 NC Flange lock nut
70 1263 * 35 35 31 22 3/8 NC x 1" HHCS GR5
71 976 * 5 5 5 5 3/8 NC x 1-1/2 HHCS GR5
72 835 * 41 41 36 36 3/8 NC Hex nut
73 3298 * 4 4 4 4 3/8 NC Hex nut plated
74 838 * 46 46 41 41 3/8 Lock washer
75 565 * 9 9 11 11 3/8 Flat washer
76 1287 * 1 2 2 2 3/8 NC Wing nut
77 4119 12 12 12 12 1/2 NF x 1 HHCS GR5
78 745 * 1 1 - - 1/2 NC x 1-1/4 HHCS GR5
79 742 * 3 3 - - 1/2 NC x 1-3/4 HHCS GR5
(NS)
80 948 * - - 3 3 1/2 NC x 2 HHCS GR5
81 1093 * 4 4 5 2 1/2 NC Hex nut
82 855 * 16 16 17 14 1/2 Lock washer
83 854 * 12 12 3 2 1/2 Flat washer
84 6268 * - - 8 8 5/8 NC x 1-1/4 HHCS GR5
REF PART A B C D DESCRIPTION