Filter
Top Products
5
the number and seriousness of kickbacks
when tested in accordance with safety re-
quirements for gasoline powered chain
saws as set by ANSI B175.1.
Small Radius Tip
Symmetrical Guide Bar
Reduced Kickback Symmetrical Guide Bar
Large Radius Tip
S
Low-Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter. Low-
Kickback Chain has met kickback per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
Low--Kickback
Chain
Not a Low--Kickback Chain
Can Obstruct
Material
Contoured Depth Gauge
Elongated Guard Link
Deflects Kickback
Force And Allows
Wood To Gradually
Ride Into Cutter
S
Handguard, designed to reduce the
chance of your left hand contacting chain if
your hand slips off the front handlebar.
S
Position of front and rear handlebars, de-
signed with distance between handles and
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
S
Chain Brake, designed to stop the chain in
the event of kickback.
ANSI B175.1-1991
“American National
Standard for Powered Tools -- Gasoline
Powered Chain Saw -- Safety Require-
ments.”
CHAIN BRAKE & CKA ANGLE
WARNING:
WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac-
tion which throws the bar and rotating chain
back and up toward the operator. Kickback
can be caused byallowing contact of the bar
tip in the danger zone with any hard object.
Kickback canalso becaused bypinching the
sawchain along thetop ofthe guide bar. This
action may push the guide bar rapidly back
toward the operator. Either of these events
may cause you to lose control of the saw
which could result in serious injury or even
death. DO NOT R ELY UPON ANY OFTHE
SAFETY DEVICES BUILT INTO YOUR
SAW. YOU SHOULD USE THE SAW
PROPERLY AND CAREFULLY TO AVOID
KICKBACK. Reduced--kickback guide bars
and low--kickback saw c hains reduce the
chance and magnitude of kickback and are
recommended. Your saw has a low kick-
back chain and bar as original equipment.
Repairs on achain brake should be made by
an authorized servicing dealer. Take your
unit to the place of purchase if purchased
from a servicing dealer, or to the nearest au-
thorized master service dealer.
WARNING:
Computed kickback
angle (CKA) listed on your saw and listed in
the CKA table below represents angle of
kickback your bar and chain combinations
will have when tested in accordance with
CSA and ANSIstandards. When purchasing
replacement bar and chain, considerations
should be given to the lower CKA values.
Lower CKA values represent safer angles to
the user, higher values indicate more angle
and higher kick energies. Computed angles
represented in the non-activated column in-
dicate total energy and angle associated
without activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain break and resulting kick angle of saw.
In all cases lower CKA values represent a
safer operating environment for the user.
S
Tip contact in some cases may cause a
lightning fast reverse REACTION, kicking
guide bar up and back toward operator.
S
Pinching the sawchain along the top ofthe
guide bar may push the guide bar rapidly
back toward the operator.
S
Either of these reactions maycause youto
lose control of the saw which could result
in serious injury. Do not rely exclusively
upon safety devices built into your saw .
The following guide bar and chain combina-
tions meet kickback r equirements of CSA
Z62.1, Z62.3, & ANSI B175.1 when used on
saws listed in this manual. Use of bar and
chain combinations other than those listed is
not recommended and may not meet the
CKA requirements per standard.
CSA Z62.1
“Chain Saws -- Occupational
Health and Safety”
CSA Z62.3
“Chain Saw Kickback Occupa-
tional Health and Safety”