Filter
Top Products
10
MAX 1/3
• Certain types of grass and grass
con di tions may re quire that an area be
mulched a second time to com pletely
hide the clip pings. When doing a sec ond
cut, mow across (per pen dic u lar) to the
fi rst cut path.
• Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.
OPERATION
MOWING TIPS
CAUTION: Do not use de-thatcher
blade attachments on your mower. Such
attachments are hazardous, will damage
your mower and could void your warranty.
• Under certain conditions, such as when
mowing very tall grass, raise the mower
height on the fi rst cut to reduce pushing
effort, to avoid over heat ing the motor,
and to avoid leaving clumps of grass
clippings. Make the second cut to the
desired height.
• For extremely heavy cutting, reduce the
width of cut.
• For side discharge operation, cut in a
coun ter clock wise di rec tion, start ing at
the outside of the area to be cut, in order
to spread grass clip pings more evenly
and to put less load on the motor. To
keep clip pings off of walkways, fl ower
beds, etc., make the fi rst cuts in a clock-
wise direction.
• When using a lawn mower in moist,
heavy grass, clumps of cut grass may
not enter the grass catcher. Reduce
ground speed (push ing speed) and/or
run the lawn mower over the area a
second time.
• If a trail of grass clipping is left on the
right side of a rear discharge lawn mow-
er, mow in a clockwise direction with a
small overlap to collect the clippings on
the next pass.
• Pores in cloth grass catchers can
become fi lled with dirt and dust with use
and the catcher will collect less grass.
To prevent this, regularly hose catcher
off with water and let dry before use.
MULCHING MOWING TIPS
IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash. See "CLEANING" in the Mainte-
nance section of this manual.
• The special mulching blade will recut the
grass clip pings many times and reduce
them in size so that as they fall onto the
lawn they will disperse into the grass
and not be noticed. Also, the mulched
grass will bio de grade quickly to provide
nu tri ents for the lawn. Always mulch with
your highest motor (blade) speed as this
will provide the best recutting action of
the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
in ter feres with the mulch ing action.
• For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades. If the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from over load ing the motor and leaving
clumps of mulched grass. For ex tremely
heavy grass, reduce your width of cut
by overlapping previously cut path and
mow slowly.
7
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind lawn mowers conform to the safety standards of the American
National Standards Institute and the U.S. Consumer Product Safety Commission.
WARNING: The blade turns when the motor is running.
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING
YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize
yourself with the location of various controls and adjustments. Save this manual for
future reference.
OPERATION
Operator presence control bar – must
be held down to the handle to start the
motor. Release to stop the motor.
Start button – used for starting the motor.
Single point height adjuster – used to
adjust cutting height of lawn mower.
Mulcher door – allows con ver sion to
discharging operation.
Mulcher door
Discharge
guard
Single point height
adjuster handle
Start button
Operator presence control bar
Wing
nut
Cam lock
Circuit breaker
Motor housing
Extension
cord
retainer
Power
cord
Handle
knob