Filter
Top Products
3
S Stop engine and allow to cool before remov-
ing fuel cap.
S Always store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAF ETY
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage trimmer head and be thrown
causing serious injury.
S Use unit properly. Use only for trimming,
mowing, and sweeping. Do not use for edg-
ing, pruning, or hedge trimming. Do not force
unit. I t will do the j ob better, a nd with less risk
of injury, at the rate for which it was designed.
S Keep fir mfootingand balance.Do notover-
reach.
S Keep all p arts of your body away from spin-
ning line and muffler . Keep engine and cutting
head below waist level. A hot muffler can
cause serious burns.
S Cut only fromyour right toyourleft. Cutting
with the line on right side of the shield will
throw debris away from the operator.
S Useonly indaylight or ingood artificial li g ht.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Stop the unit when not in use.
S Carry or transport the unit with engine
stopped.
S Allow the engineto cool; secure unit before
storing or transporting in vehicle.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
S Store unit andfuel inan areawhere fuelva-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Store the unit out of the reach of children
WARNING: Theengine exhaust from
this product contains chemicals known to the
State of California to cause cancer, birth de-
fects or other reproductive harm.
SPECIAL NOTICE: This unit is not
equipp ed w ith atempera ture l im iting m uf flerand
spark arresting screen which m eets the require-
ments o f California Codes 4442 and 4443. All
U.S. forest land and the states of California, Ida-
ho, Maine, Minnesota, New Jersey, Oregon,
and Washington require by law that many inter-
nal combustion engines to b e e quipped with a
spark arrestor screen. If you operate in a locale
where such regulations exist, you are legally re-
sponsible forinstalling and m aintaining theoper-
ating condition of these parts. Failure to do so is
a violation of the law. If a spark arrestor is re-
quired i nyourarea, contactyour au thorizedser-
vice de aler for the pr oper kit.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation d isorders or abnor-
mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If sympto ms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool a nd seek medical attention. An
anti-vibration system does not guarantee the
avoidance of these problems. Users who o per-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this to ol.
ASSEMBLY
WARNING: If received assembled,
repeat allsteps toensure your unitis properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filt er to rattle in the
empty fuel tank.
Finding fuel oroil residue on m uffler is nor m al
due to carburetor adjustments and testing
done by th e manufacturer .
ATTACH THE HANDLE
1. Remove upper wing nut and curved head
tube bolt from upper handle.
2. Loosen lower wing nut on lower handle.
3. Insert upper handle over lower handle.
NOTE: Ensure upper handle grips are in
position asshown i nthe followingillustrations
(throttle handle grip on left side).
4. Align holes and insert curved head tube
bolt through upper and lower handles.
5. Re--installandsecurelytighten upperwing
nut onto bolt.
6. Retighten lower wing nut securely.
Upper handle
Upper wing nut
Lower handle
Lower wing nut
Tube bolt