Weed Eater 530087688 Blower User Manual


 
-- 5 --
S
To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S
To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S
Use r akes and brooms to loosen debris be-
fore blowing.
S
In dusty conditions, slightly dampen sur-
faces or use a mister attachment when wa-
ter is available.
S
Conserve water by using power blow er s
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, por ches, and gardens.
S
Watch out for children, pets, open windows,
or freshly washed cars. Blow debris away
safely.
S
Use the full blower nozzle extension so the
air stream can work close to the ground.
S
After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
FUELING
WARNING:
Remove fuel cap slowly
when refueling.
This engine is certified to operate on
unleaded gasoline. Before operat ion,
gasoline must be mixed with a good quality
2-cycle air-cooled engine oil. We recommend
Poulan/Weed Eater brand oil. Mix gasoline
and oil at a ratio of 40:1 (A 40:1 ratio is
obtained by mixing 3.2 ounces of oil with 1
gallon of unleaded gasoline). When mixing
fuel, follow the instructions printed on the
container. Always read and follow safety
rules under HANDLE FUEL WITH CAUTION
in the safety rules section.
STARTING
TO STOP THE ENGINE
D
To stop the engine, press and hold the
switch in the
STOP
position until engine
comes to a complete stop.
BEFORE STARTING THE ENGINE
D
Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
D
Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
Blower
Vacuum
STARTING POSITION
WARNING:
When starting engi ne,
hold the unit as illu strated. Do n o t set u n it on a n y
surface except a clean, hard area when st arting
engine or while engine is running. Debris such
as gr avel, s and, dust, gr ass, etc. coul d be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing ser ious injury to by-
standers or the operator.
STARTING A COLD ENGINE OR
W ARM ENGINE THAT HAS RUN OUT
OF FUEL
S
Move throttle lever to the
position.
S
Move choke lever to FULL CHOKE.
S
Slowly press the primer bulb 12 times.
Switch
Throttle
Lever
Choke
Lever
Primer
Button
S
Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls (be-
low 30
_
F, 8 pulls).
NOTE:
If engine attempts to start before the
5
th
pull, go to next step immediately.
S
Move the choke lever to HALF CHOKE.
S
Pull the starter rope sharply until the engine
runs, but no more than 5 pulls (below 30
_
F,
10 pulls). Run engine for 5 seconds, then
move choke lever to OFF CHOKE.
S
Allow the unit to run for 30 more seconds at
OFF CHOKE before moving the throttle le-
ver to
position.
If engine has not started after 5 pulls (at HALF
CH O KE), repeat ST ARTING A COLDENG INE
procedure. If engine st ill does not start, proceed
to STARTING A FL OODED ENGIN E.
STARTING A WARM ENGINE THAT
HAS NOT RUN OUT OF FUEL
S
Move throttle lever to the
position.
S
Pull starter rope sharply until engine runs,
but no more than 5 pulls.
NOTE
:
If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.