Filter
Top Products
10
SWEEPIN G
-- The fanningaction of therotating
line canbe usedto blowaw ayloose debr isfrom
an area. Keep the line par allel to and above the
area surface and sw ing the tool from side to
side.
OPERATING INSTRUCTIONS FOR
USE WITH WEED BLADE
S
Blade Thr ust
is a r eaction that only occurs
when using a bladed unit. This reaction can
cause serious injury such as amputation.
Carefullystudythissection.Itis im por tantthat
you understand what causes blade thrust,
how you can reduce the chance of its
occurring, and howyou can remain in control
of unit if blade thrust occur s.
S
WHA T CAUSES BLADE THRUST
--
Blade
Thrust
can occur when the spinning blade
contacts an object that it does not cut. This
contact causesthebladetostopforaninstant
and then suddenly move or “thrust” away
from the obj ect that w as hit. The “thrusting”
reaction can be violent enough to cause the
operator to be propelled in any direction and
lose control of the unit. The uncontrolled unit
can cause ser ious injury if the blade contacts
the operator or others.
S
WHEN BLADE T HRUST OCCURS
--
Blade Thrust
can occur without warning if
the blade snags, stalls, or binds. This is
more likely to occur in areas where it is
difficult to see the material being cut. By
using the unit properly, the occurrence of
blade thrust will be reduced and the
operator will be less likely to lose control.
S
Cutonly grass,weeds,and woody brushup
to 1/2 inch in diameter with the weed blade.
Do not let the blade contact material it
cannot cut such as stumps, rocks, fences,
metal, etc., orclusters of hard, woodybrush
having a diameter greater than 1/2 inch.
S
Keep the blade sharp. A dull blade is more
likely to snag and thrust.
S
Cut only at full throttle. The blade will have
maximum cutting power and isless likely to
bind or stall.
S
“Feed” the blade deliberately and not too
rapidly.The blade can thrust away ifit isfed
too rapidly.
S
Cutonly fromyourlefttoyour right. Cuttingon
right side of the shield will throw debris away
from the oper ator.
S
Use the shoulder strap and keep a firm grip
on the unit with both hands. A properly
adjusted shoulder st rap will support the
weight of the unit, freeing your arms and
handstocontrol and guidethe cuttingmotion.
S
Keep feet comfortably spr ead apart and
braced for a possible sudden, rapid thrust of
unit. Do not overreach. Keep firm footing and
balance.
S
Keep blade below waist level; it will be
easier to maintain control of unit.
S
Donot raise theengine above yourwaist as
the blade can come dangerously close to
your body.
S
Do not swing unit with such force that you
are in danger of losing your balance.
Bring the engine to cutting speed before en-
tering the material to be cut.If the blade does
not turn whenyousqueeze the throttle trigger,
make sure tube is fully ins erted into the en-
gine.
Always release the throttle trigger and allow
engine to return to idle speed when not cut-
ting. The blade should not turn while the en-
gine isrunning at idle. If the bladeturns atidle,
do not use your unit. Refer to the CARBURE-
TOR ADJUSTMENT section or contact your
authorized service dealer.
S
Maintain good firm footing while using the
unit. Do this by planting feet firmly in a
comfortable apart position.
S
Cut while swinging the upper part of your
body from left to right.
S
Asyoumoveforward tothe nextarea tocut,
be sure to maintain your balance and
footing.
Cut using the 2
o’clock to 4 o’clock
position of the
blade
2 o’clock
4 o’clock
RECOMMENDED CUTTING POSITION
WARNING:
The operator or others
mustnot tryto clearaway cutmaterial withthe
engine running or the blade turning to avoid
serious injury. Stop engine and blade before
removing materials wrapped around blade or
tube.