Filter
Top Products
Perform the above steps in the opposite order after oil has
finished draining.
5. Refill the engine with new motor oil as instructed in the
Engine Operator/Owner Manual packed with your machine.
NOTE: Refer to the Engine Operator/Owner Manual packed with
your unit for information regarding the quantity and proper
viscosity of motor oil.Air Cleaner
Service the pre-cleaner and cartridge/air cleaner element as
instructed in the Engine Operator/Owner Manual packed with
your unit.
Spark Plug
The spark plug should be cleaned and the gap reset once a
season. Spark plug replacement is recommended at the start
of each mowing season. Refer to the Engine Operator/Owner
Manual for correct plug type and gap specifications.
Lubrication
WARNING: Before lubricating, repairing, or
inspecting, always disengage PTO, move shift lever
into neutral position, set parking brake, stop engine
and remove key to prevent unintended starting.
Engine
Lubricate the engine with motor oil as instructed in the Engine
Owner Manual packed with your unit.
Pivot Points & Linkage
Lubricate all the pivot points on the drive system, parking brake
and lift linkage at least once a season with light oil.
Rear Wheels
The rear wheels should be removed from the axles once a
season. Lubricate the axles and the rims well with an all-purpose
grease before re-installing them.
Cleaning the Engine And Deck
Any fuel or oil spilled on the machine should be wiped off
promptly. Do NOT allow debris to accumulate around the cooling
fins of the engine or on any other part of the machine.
IMPORTANT: The use of a pressure washer to clean your
tractor is NOT recommended. It may cause damage to electrical
components, spindles, pulleys, bearings or the engine.
Deck Wash System™ (If equipped)
Some tractors come fitted with a Deck Wash System™, which
is used to rinse grass clippings from the deck’s underside and
prevent the buildup of corrosive chemicals. Other tractors may
have a deck wash plug, allowing for a Deck Wash System™ that
can be added at a later time. If this is the case, a hex bolt and
washer can be found on your tractor’s deck surface and can be
replaced with a water port to be used as part of a separately-
available deck wash system.
NOTE: Refer to the Attachments & Accessories section of this
manual for information regarding this and other separately-
available attachments and accessories for your tractor.
To utilize the Deck Wash System™, complete the following steps
AFTER EACH MOWING:
1. Drive the tractor to a level, clear spot on your lawn, near
enough for your garden hose to reach.
CAUTION: Make certain the tractor’s discharge
chute is directed AWAY from your house, garage,
parked cars, etc.
2. Disengage the PTO (Blade Engage), set the parking brake
and stop the engine.
3. Thread the hose coupler (packaged with your tractor’s
Operator’s Manual) onto the end of your garden hose.
4. Attach the hose coupler to the water port on the deck’s
surface. See Figure 6-3.
Figure 6-3
5. Turn the water on.
6. While sitting in the operator’s position on the tractor, start
the engine and place the throttle lever in the FAST (rabbit)
position.
7. Move the tractor’s PTO (Blade Engage) into the ON position.
8. Remain in the operator’s position with the cutting deck
engaged for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly rinse.
9. Move the tractor’s PTO (Blade Engage) into the OFF
position.
10. Turn the ignition key to the STOP position to turn the
tractor’s engine off.
11. Turn the water off and detach the hose coupler from the
water port on your deck’s surface.
12. Repeat steps 4 through 11 on the opposite side of the
cutting deck if a second water port is present.
IMPORTANT: After cleaning your deck with the Deck Wash
System™ , return to the operator’s position and engage the PTO.
Keep the cutting deck running for a minimum of two minutes,
allowing the underside of the cutting deck to thoroughly dry.
20 Section 6— Maintenance & adjuStMentS