Filter
Top Products
GB-2
Attention: Danger! Rotating machinery.
8. The hedge trimmer should always be held with
both hands.
9. Before using the equipment clear the working
area of any foreign objects and be aware of
foreign objects during operation of the machine!
If the machine becomes jammed e.g. by thick
branches, switch off and disconnect the machine
from the mains socket before investigating and
rectifying the cause of the jam. Take special care
when switching the machine on again.
10. Check the flex and all connections for any visible
faults before using the machine (plug discon-
nected). Do not use a faulty flex.
11. Keep the flex away from the cutting area.
12. Do not use the trimmer in wet weather and do
not use it to cut wet hedges.Do not wash down
the device with water. Do not use any high-
pressure cleaning devices or steam jet devices
for cleaning.
13. Carry the trimmer by the handles provided and
keep hands away from the cutting blades.
14. In line with agricultural Trade Association Regu-
lations only persons over the age of 17 may work
on their own with electric hedge trimmers. Use
is permitted for persons over 16 years if the work
is carried out under the supervision of adults.
15. We would recommend that safety clothing is
worn during the work and that eyes, ears, hair,
hands and feet are fully protected. Protective
gloves should also be worn.
16. Ensure that the motor of your hedge shears can
not be switched on by mistake when you put it down
after work or when you are going to clean the
device. Never forget to unplug the mains supply!
17. Check the cutting unit regularly for damage and
if damage is discovered, the cutting unit should
be properly repaired.
18. Be aware of your responsibility as user towards
third parties in the working area.
19. The trimmer must be properly checked and
serviced. If the blades get damaged they should
only be exchanged in pairs. In the event of damage
from impact, specialist’s inspection is essential.
20. Only use extension cords that are approved for
outdoor use and that are not lighter than rubber
tube cords type H07 RN-F according to DIN/VDE
0282 with a diameter of at least 1.5 mm
2
. They
must be water spray protected. Damaged cables
of this unit are only to be replaced by a service
station designated by the manufacturer as spe-
cial tools are necessary. Equipment which will
be used in different outside locations should be
connected via residual current - operated cur-
rent breakers.
21. Do not use the cable for purposes it has not been
designed for. Never carry a power tool at its cable.
Do not pull out the plug from the socket using
the cable. Protect the cable from heat, oil and
sharp edges.
22. Ensure that the equipment is stored safely after
use in such a way that the blade cannot be touched.
23. When using the equipment, hold it securely with
both hands, stand firmly and ensure that you have
sufficient working space. There should be no
people, animals or objects within the working
area. Select the cutting height so that the blade
does not make contact with the ground and you
can operate the equipment from a secure position.
24. Take care when transporting the equipment (only
with blade cover!).
25. For initial use of the hedge trimmer we would
recommend that in addition to reading the oper-
ating instructions, you also seek a practical
demonstration from an expert.
26. Always ensure that all protective devices and
handles are properly fitted.
27. Never try to use an incomplete tool or a tool that has
been modified in a way that has not been approved.
28. Do not allow children to use a power tool.
29. The use of the hedge trimmer is to be avoided if
other persons, above all children, are within the
working area.
30. Familiarize yourself with the working area and pay
attention to possible dangers which you might not
be able to hear due to the noise of the machine.
31. Always pay attention. Take care of what you do.
Do your work sensibly. Do not use a power tool
if you cannot concentrate.
32. ATTENTION ! Only use the accessories or attach-
ments shown in the Operating Instructions. The
use of other add-on tools and accessories may
set up the risk of injury for you.
33. Have your power tools repaired by an appro-
priately qualified electrician only. This power tool
complies with the applicable safety regulations.
Repairs must only be carried out by qualified
electricians using original spare parts; otherwise,
accidents may occur to the user.
5. Before use
Safety Guard (Fig. 2)
Push the supplied hand guard (3) over the blades and fix
securely with each 2 screws on both sides of the housing
according to fig. 2. The safety shield prevents touching
the blades during operation. Hold tool with both hands!
Power connection
The machine can only be connected to a single-phase a.c.
current connection. The machine is protectively insulated in
accordance with classification II of VDE 0740. Before using
the machine ensure that the mains current agrees with the
operating voltage data on the machine’s identification plate.
Power Circuit Breaker
Machines which will be used in different outside loca-
tions must be connected to a Power Circuit Breaker.
Securing the extension lead (Fig. 3)
Only use extension leads suitable for outside use. The cross
section of the wire (max. length of extension cord: 75m)
must be at least 1,5 mm². Secure the connection between
the device’s power cord and the extension cable by leading
the extension cable through the strain relief in the housing
(Fig. 3).