Filter
Top Products
60
ENGLISH
EN
2.4.9 Ignition lock (4,5:I)
Ignition lock used for starting/stopping the engine.
There are 3 positions:
1. Stop position – the engine is short-cir-
cuited. The key can be removed.
2. Operating position
3. Start position – the electric start motor
is activated when the key is turned to the
spring-loaded start position. Once the en-
gine has started, let the key return to oper-
ating position 2.
NOTE! If the engine should stop for any reason,
the key cannot be turned directly to position 3
due to a mechanical ignition lock. To start the
engine - turn the key back to position 1 and then
to positions 2 and 3.
2.4.10 Power take-off (4,5:K)
A lever for engaging and disengaging the power
take-off for operating front-mounted accessories.
Two positions:
1. Lever in forward position – power take-
off disengaged.
2. Lever in backward position - power
take-off engaged.
2.4.11 Hour meter (2:P)
Indicates the number of working hours. Only
works when the engine is running.
2.4.12 Cruise control (4:N) (4WD)
A switch for activating the cruise control. The
cruise control locks the pedal (3:F) in the desired
position.
1. Press down the pedal (3:F) until the de-
sired speed is obtained. Then press the
front part of the switch to activate the
cruise control. The symbol will light up.
2. Disengage the cruise control by releas-
ing it with the pedal (3:B) or pressing the
rear part of the switch.
2.4.13 Cutting height adjustment (4,5:J)
The machine is equipped with a control for using
the cutting deck with electrical cutting height ad-
justment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (2:Q).
2.4.14Rear Rake (4:L) (4WD)
The machine is fitted with a control for electrical
adjustment of a rear rake (available as an
accessory).
The switch is used to raise and lower the
rear rake.
Cables for connecting the rear rake are found at the
rear of the machine, to the left of the upper side of
the bumper. (4WD is prepared for a rear rake,
cables routed).
2.4.15 Sand spreader (4:O)
(4WD)
The machine has been designed for electrical ad-
justment of a sand spreader (accessory).
The switch is used to start and stop the
spreader.
Cables for connecting the sand spreader are at the
rear of the machine.
2.4.16Clutch release lever
A lever for disengaging the variable transmission.
2WD is equipped with a lever, connected to the
rear axle. See (6:R).
4WD is equipped with two levers, connected to the
rear axle (7:A) and the front axle (7:B).
The levers enable the machine to be moved by
hand without the help of the engine. Two positions:
1. Lever in the inner position –
transmission engaged for normal
operation.
2. Lever in the outer position –
transmission disengaged. The
machine can be moved by hand.
The machine may not be towed over long distances
or at high speeds. The transmission could be dam-
aged.
The machine must not be operated with
the forward most lever in the outer po-
sition. Risk of damage and oil leakage in
the front axle.
2.4.17 Seat (1:T)
The seat can be folded and adjusted front-
rear. The seat can be adjusted as follows:
1. Move the control lever (1:T) upwards.
2. Set the seat to the desired position.
3. Release the control lever (1:S) to lock
the seat.
The seat is equipped with a safety switch that is
connected to the machine’s safety system. This
means that certain dangerous activities are not pos-
sible when there is nobody sitting on the seat. Also
see 4.5.2.
12V