Filter
Top Products
Safety / Operation 2
For parts or assistance, call Simer Customer Service at 1-800-468-7867
ATTENTION: Read carefully before attempting to
install, operate or service your pump. Protect your-
self and others by observing all safety information
and additional instructions included with this equip-
ment. Failure to comply with instructions could
result in personal injury and/or property damage!
Retain for future reference.
DESCRIPTION
This submersible pump is intended for water removal
from swimming pool covers. Unit is constructed of
hi-impact corrosion resistant plastic. Screened inlet
prevents large solids from entering pump.
SPECIFICATIONS
Power supply required........................115V, 60 HZ.
Motor ..........................................................16 Watt
Motor duty.............................................Continuous
Thermal Protector....................................Automatic
Liquid Temp. Range......................Max. 77°F (25°C)
Operation Position..................................Horizontal
Circuit Requirement (min.)..........................10 Amp
Dimensions (Overall)................6-3/8" x 4-7/8” x 3”
Power Cord Set .................................Vinyl, 3-prong
Discharge.....Horizontal Male Garden Hose Thread
PERFORMANCE
NOTICE: This unit is not designed for applications in-
volving salt water or brine!
GENERAL SAFETY
INFORMATION
1. Know the pump application, limitations, and
potential hazards.
Do not use in explosive
atmospheres. Pump water only with this pump.
Failure to follow this warning can result in per-
sonal injury and/or property damage.
2. Make certain that the power source conforms to
the requirements of your equipment.
3. Disconnect power before servicing.
4. Secure the discharge line before starting the
pump. An unsecured discharge line will whip,
possibly causing personal injury and/or property
damage.
5. Check hoses for weak or worn condition before
each use, making certain that all connections are
secure.
6. Periodically inspect pump and system compo-
nents. Perform routine maintenance as required
(See MAINTENANCE Section).
7. Provide a means of pressure relief on pumps
whose discharge line can be shut-off or obstructed.
8. Personal Safety:
a. Wear safety glasses at all times when work-
ing with pumps.
b. Keep work area clean, uncluttered and prop-
erly lighted – replace all unused tools and
equipment.
c. Keep visitors at a safe distance from the work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter
keys.
9. This equipment is only for use on 115 volt (sin-
gle phase) and is equipped with an approved 3-
conductor cord and 3-prong, grounding-type
plug.
To reduce the risk of electric
shock, be certain that it is connected to a prop-
erly grounded, Ground Fault Circuit Interrupter
(GFCI) protected, grounding-type receptacle.
Do not lift pump by the power cord; always lift
it by the handle.
Where a 2-prong wall receptacle is encoun-
tered, it must be replaced with a properly
grounded, GFCI protected, 3-prong receptacle
installed in accordance with all applicable
codes and ordinances.
10. Protect electrical cord from sharp objects, hot
surfaces, oil, and chemicals. Avoid kinking the
cord. Replace or repair damaged or worn cords
immediately.
11. Do not touch an operating motor. Modern motors
can operate at high temperatures.
12. Power Supply: Pump is designed for 115V., 60
HZ. operation and requires a circuit of 10
amperes or more capacity. It is supplied with a
3-wire cord set with grounding-type plug for
use in a 3-wire, grounded outlet. To reduce risk
of electrical shock, plug pump into a Ground
Fault Circuit Interrupter (GFCI). Consult a local
electrician for availability and installation. For
safety, circuit should always be electrically
grounded to a suitable electrical ground such as
a grounded water pipe or a properly grounded
metallic raceway, or ground wire system. Do
not cut off the round grounding prong.
OPERATION
Risk of electric shock. Do not han-
dle a pump or pump motor with wet hands or when
standing on wet or damp surface, or in water.
1. Hand tighten 90-degree garden hose discharge
adapter into top of pump.
2. Thread garden hose onto adapter hand tight.
Then turn one quarter turn tighter with pliers to
seal. Make sure the washer is in the end of the
garden hose.
3. Straighten out the garden hose as much as
possible.
GPH IN TOTAL FEET
3' 5' 7'
2105 300 170 0