Support User Manuals

Ryobi CS30 Trimmer User Manual

Open as PDF

of 14

fl

rl

:1

i

,t

T:

ri

ATTACHING

THE SHOULDER HARNESS

-

BC30

See

Figure

9.

I

Connect the latch on

the

shoulder

harness to the strap

hanger.

r

Adjust the

strap

to a comfortable

position.

CONVERTING

FROM BRUSHCUTTER TO

STRING TRIMMER

-

BC3O

To

convert

from the brushcutter to the string trimmer, remove

the

blade and

brushcutter

guard,

attach the straight shaft

grass

deflector

and install the string head.

REMOVING THE TRI-ARC@ BLADE AND

BRUSHCUTTER GUARD

See

Figures 10

-

1 1.

r

Align

the slot

in the flanged washer with the slot in the

gear

head.

I

Place the

gear

head locking tool through the slot in the

flanged washer and

gear

head.

I

Remove

the blade nut by turning it clockwise.

r

Remove the cupped

washer

and

the blade.

r

Remove the flanged

washer

from

the

gear

head

shaft

and

retain it for the

string

head installation.

r

Remove

the three

screws securino

the

brushcutter ouard

to

gear

head.

I

Remove

the

brushcutter

guard.

NOTE: Store the brushcutter

parts

together for Iater use.

INSTALLING THE

STRAIGHT

SHAFT GRASS

DEFLECTOR AND

STRING

HEAD

See

Figures 10

-

12.

r

Install

the

grass

def lector. Refer to To Attach the Straight

Shaft Grass

Deflector earlier in this manual.

I

Place

the flanged washer

on

the

gear

head shaft.

NOTE: The hollow side of

the flanoed washer should face

the

gear

head.

r

Align the slot in the flanged washer

with the slot in the

gear

head.

I

Place the

gear

head locking tool

through the slot in the

flanged

washer

and

gear

head.

r

Install

the

string head assembly onto the

gear

head shaft

by

turning

counterclockwise.

I

Tighten

the string

head assembly securely.

CONVERTING

FROM

STRING TRIMMER

TO

BRUSHCUTTER

-

BC3O

To

convert

from the

string trimmer

to

the

brushcutter,

remove

the

string

head assembly

and straight shaft

grass

deflector,

attach

the

brushcutter

guard

and

install the

blade.

ATTACHING

THE GRASS

DEFLECTOR

A

unrulnc'

The

line cutting

blade

on

the

grass

deflector

is

sharp.

Avoid

contact

with the blade. Failure

to

avoid

contact

can

result

in serious

personal

injury.

TO

ATTACH

THE CURVED

SHAFT

GRASS

DEFLECTOR

-

CSSO

See

Figure 6.

I

Remove

hex screw,

flat

washer, lock washer, and

wing

nut

from

grass

deflector.

r

Press

the

grass

deflector onto the bottom of

the curved

shaft

as shown.

r

Insed

the

hex screw ihrough the

grass

deflector

and

the

bracket on

the curved shaft.

I

Place the

flat washer and lock

washer on the

hex head

cap

screw.

r

Place

the

wing nut on the

hex head cap screw and

tighten

securely.

TO ATTACH

THE

STRAIGHT

SHAFT

GRASS

DEFLECTOR.

SS3O

See

Figure 7.

I

Remove

the

wing screw

from the

grass

deflector.

r

lnsert

the tab

on the mounting

bracket

in the slot

on the

grass

deflector.

r

Align ihe screw

hole

in the mounting

bracket

with the

screw

hole in the

grass

deflector.

r

Insert

the wing screw

through

the mounting

bracket and

into the

grass

deflector.

I

Tighten

the screw

securely

ATTACHING

THE BRUSHCUTTER

GUARD

BC30

See

Figure 8.

The

guard

is shipped

installed

on

these

brushcutter

models. Instructions

have been

included

for

reference

when

changing

from string trimmer

operation

back

to brushcutter

operation.

I

Withthestring

head

removed,

placethebrushcutterguard

on the

gear

head as shown.

I

Install

the three

hex head screws

from bottom

through

the

guard

and

into the

gear

head.

I

Tighten

the screws securely

and

torque

to 40-50

in

lb.

mtntmum.

t,

HEX

SCREW

'ah'

\

BRACKET

\

W--*hBi[*

4/\

WASHER

WING NUT

GEAR HEAD

FLANGED WASHER

>/

'@,1

'll'J'hlt'+'

sLoT<@\.

/

previous next