Remington 76728K, 099178H, 100089-06, 100089-08,107709-01,075762J, 098031J, 099039J, 100089-04, 100089-05, 100089-07, 107714-02,104316-04, 106890-01, 104317, 106821 Chainsaw User Manual


 
3
107990
OWNER’S MANUAL
For more information, visit www.desatech.com
Kickback Safety Devices On
This Saw
This saw has a low-kickback chain and
reduced kickback guide bar. Both items
reduce the chance of kickback. Kickback
can still occur with this saw.
Properly install front hand guard. This item
can reduce injuries from kickback. Follow
assembly instructions on page 6. Do not
remove front hand guard. Do not replace
front hand guard with substitute.
The following steps will reduce the risk of
kickback.
Use both hands to grip saw while saw is
running. Use firm grip. Thumbs and
fingers must wrap around saw handles.
•Keep all safety items in place on saw.
Make sure they work properly.
Do not overreach or cut above shoulder
height.
Keep solid footing and balance at all
times
Stand slightly to left side of saw. This
keeps your body from being in direct line
with chain.
Do not let guide bar nose touch anything
when chain is moving (see Figure 1).
Direction
90°
Quadrant
Figure 1 - Kickback Hazard Example: Do
Not Let Nose of Guide Bar Touch Object
While Chain is Moving
Do Not Let
Guide Bar
Touch Here
MAINTENANCE AND
STORAGE OF CHAIN SAW
1. Unplug chain saw from power source
when not in use
before moving from one place to an-
other
before servicing
before changing accessories or at-
tachments, such as saw chain and
guard
2. Inspect chain saw before and after each
use. Check saw closely if guard or other
part has been damaged. Check for any
damage that may affect operator safety
or operation of saw. Check for align-
ment or binding of moving parts. Check
for broken or damaged parts. Do not
use chain saw if damage affects safety
or operation. Have damage repaired by
authorized service center.
3. Maintain chain saw with care.
Never expose saw to rain.
Keep chain sharp, clean, and lubri-
cated for better and safer performance.
Follow steps outlined in this manual
to sharpen chain.
•Keep handles dry, clean, and free of
oil and grease.
Keep all screws and nuts tight.
Inspect power cord often. If dam-
aged, have repaired by authorized
service center.
Never carry chain saw by power cord.
Never yank power cord to unplug it.
Keep power cord from heat, oil, and
sharp edges.
Inspect extension cords often and
replace if damaged.
4. When servicing, use only identical re-
placement parts.
5. When not in use, always store chain saw
in a high or locked place, out of
children’s reach
in a dry place
in a carrying case or with scabbard
over guide bar
Keep this manual for reference. It is your
guide to safe and proper operation of this
chain saw.
•Never try cutting through two logs at
same time. Only cut one log at a time.
Do not bury guide bar nose or try plunge
cut (boring into wood using guide bar
nose).
•Watch for shifting of wood or other
forces that may pinch chain.
Use extreme caution when reentering a
previous cut.
Use low-kickback chain and guide bar
supplied with this chain saw. Only re-
place these parts with chains and guide
bars listed in this manual.
Never use dull or loose chain. Keep chain
sharp with proper tension.
Do not hand sharpen chain on automatic
chain sharpening (Fast Sharp) models.
Saw Maintenance and Kickback
Safety
Follow maintenance instructions in this
manual. Proper cleaning of saw and chain
and guide bar maintenance can reduce
chances of kickback. Inspect and maintain
saw after each use. This will increase the
service life of your saw.
Note:
Even with
proper sharpening, risk of kickback can
increase with each sharpening.
WARNING: Kickback may oc-
cur when the nose or tip of the
guide bar touches an object, or
when the wood closes in and
pinches the saw chain in the cut.
Tip contact in some cases may
cause a lightning fast reverse re-
action, kicking the guide bar up
and back towards the operator.
Pinching the saw chain along the
top of the guide bar may push the
guide bar rapidly back towards
the operator. Either of these re-
actions may cause you to lose
control of the saw which could
result in serious injury to user.
KICKBACK
SAFETY
WARNINGS