Remington 098031J Chainsaw User Manual


 
21
108539 www.desatech.com
4. Hold file guide level. Make sure 30° mark on
file guide is parallel to center of guide bar (see
Figure 19). This will insure that you file cutters
at 30° angle.
5. File from inside towards outside of cutter until
sharp. Only file in this one direction (see Figure
19).
Note:
Two or three strokes with file should
sharpen cutter.
6. After each cutter is sharpened, move chain for-
ward to sharpen next cutter. File all cutters on
one side of chain.
7. Move to other side of chain and repeat process.
Filing Cutter Depth Gauges
The cutter depth gauge clearance is reduced as cut-
ters are sharpened. After every second or third sharp-
ening, reset cutter depth gauges.
1. Place depth gauge tool (.025") firmly across top
of two cutters. Make sure depth gauge enters slot
in depth gauge tool (see Figure 21).
2. Use medium flat file. File depth gauge level with
depth gauge tool.
3. Remove depth gauge tool. With flat file, round
off front corner of cutter depth gauge (see Fig-
ure 22).
After several hand filings, have authorized service
center or sharpening service machine sharpen chain.
This will insure even filing.
REPLACING SAW CHAIN
Replace chain when cutters are too worn to sharpen or
when chain breaks. Only use replacement chain noted
in this manual. Always include new drive sprocket when
replacing chain. This will maintain proper driving of
chain.
Note:
For proper chain and drive sprocket, see
Replacement Parts and Accessories.
CLEANING AND
MAINTENANCE
Continued
TECHNICAL SERVICE
You may have further questions about assembling,
operating, or maintaining this saw. If so, contact
DESA International’s Technical Service Department
at 1-800-858-8501.
You can also visit DESA International’s technical
service web site at www.desatech.com.
SERVICE PUBLICATIONS
You can receive an illustrated parts list free of charge.
Send a self-addressed stamped envelope to address
on back page of this manual.
When writing, include model number and serial num-
ber of saw. You will find these numbers on saw mo-
tor housing decal.
REPLACEMENT PARTS
AND ACCESSORIES
WARNING: Use only replacement
parts and accessories described in this
manual. Use of other parts or accessories
could damage saw or injure operator.
For a list of Authorized Service Centers or Parts Dis-
tributors near you, call 1-800-858-8501 or visit our
website at www.desatech.com.
You may purchase the following service or replace-
ment parts:
LNT-2
Part Number Description
104302-01S
#
Guide bar, 8" (20.3 cm)
104301S
#
Chain, 8" (20.3 cm)
097567-01S Guide bar, 10" (25.4 cm)
091371S Chain, 10" (25.4 cm)
097568-02S Guide bar, 12" (30.5 cm)
091373-02S Chain, 12" (30.5 cm)
075752 Drive Sprocket
099178H, 100089-06, 100089-07 & EL-1
Part Number Description
097570-01S Guide bar, 14" (35.5 cm)
091374-02S Chain, 14" (35.5 cm)
075752 Drive Sprocket
DESA International
P.O. Box 90004
Bowling Green, KY 42102-9004
1-800-858-8501
Parts Department
STORAGE
If storing saw for more than 30 days, follow steps below.
1. Drain oil tank.
2. Remove and clean guide bar and chain. Clean
guide bar and chain by soaking in petroleum
based solvent or mild soap and water mixture.
3. Dry guide bar and chain.
4. Place chain in container filled with oil. This will
prevent rust.
5. Wipe a thin coating of oil over surface of guide bar.
6. Wipe off outside of saw body. Do this with soft cloth
dampened with a mild soap and water mixture.
7. Store chain saw
in a high or locked place, out of children’s reach
in a dry place
in a carrying case or with scabbard over guide bar
Continued
#
Must order both pieces