Poulan 545137251 Chainsaw User Manual


 
3
gloves; eye protection such as non-fog-
ging, vented goggles or face screen; an
approved safety hard hat;andsoundbarri-
ers (ear plugs or mufflers) to protect your
hearing. Regular users should have hear-
ing checked regularly as chain saw noise
can damage hearing. Secure hair above
shoulder length.
Snug
Fitting
Clothing
Safety
Shoes
Safety Chaps
Heavy Duty
Gloves
Eye
Protection
Hearing
Protection
Safety Hat
S Keep all parts of your body away from the
chain when the engine is running.
S Keep children, bystanders, and anim als a
minimum of 30 feet (10 meters) away from
the work a rea. Do not allow other people
or animals to be near the chain saw w hen
starting or operating the chain saw.
S Do not handle or oper ate a chain saw when
you are fatigued, ill, or upset, or if you have
taken alcohol, drugs, o r medication. You
must be in good physical condition and m en-
tally alert. Chain saw work is strenuous. If
you have a ny condi tion that might b e aggra-
vated by strenuous work, check with your
doctor before o pe rating a chai n saw.
S Carefully planyour sawingoperation inad-
vance. Do notstartcutting untilyou havea
clear work area, securefooting, and, ifyou
are f elling trees, a planned retreat path.
OPERATE YOUR SAW SAFELY
S Do notoperate achain saw with one hand.
Serious injury to the operator, helpers, by-
standers or any combination of these per-
sons may result from one-handed opera-
tion. A chain saw is intended for
two-handed use.
S Operate the chain saw only in awell-venti-
lated outdoor area.
S Do not operate saw from a ladder or in a
tree.
S Make sure the chain will not make contact
with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
S Do not put pressure on the saw at the end o f
the cut. Applying pr essure can cause you to
lose control when the cut is completed.
S Stop the engine before setting the saw
down.
S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brakeimmediately if it becomes damaged,
broken or is otherwise removed.
S With the engine stopped, hand carry the
chain saw with the muffler away f rom your
body , and the guide bar and chain to the
rear, p referably covered with a scabbard.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Have allchain s aw service performed by a
qualified service dealer with the exception
of the items listed in the maintenance sec-
tionof this manual. For example, ifimprop-
er tools are used to remove or hold the fly-
wheel when servicingthe clutch, structural
damage to the flywheel can occur and
cause the flywheel to burst.
S Make certain the saw chain stops moving
when the throttle trigger is released. For
correction, refer to CARBURETOR AD-
JUSTMENT.
S Never modify your saw in any way.
S Keep the handles dry, c lean, andfree of oil
or fuel mixture.
S Keep fuel and oil caps, screws, and fas-
teners securely tightened.
S Use o nly Poulan a cc essories and rep lace-
ment parts as recommended.
HANDLE FUEL WITH CAUTION
S Do not smoke while handling f uel or w hile
operating the saw.
S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
There should benosmoking, openflames,
or work thatcould cause sparks. Allow en-
gine t o cool before r efueling.
S Mix and pour fuel in an outdoor area on
bare g round; store fuel in a cool, dry , well
ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up all fuel spills before starting saw.
S Move at least 10 feet (3 meters) from fuel-
ing site before starting engine.
S Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and r efuel unit.
S Storethe unitandfuel inanarea where fuel
vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.
KICKBACK
WARNING: Avoid kickback which
can r esult in serious injury. Kickback is the
backward, upw ardor suddenforward motion
of the guide bar occurring when the saw
chain near theupper tip of theguide barcon-
tacts any object such as a log or branch, or
when the wood closes in and pinches the
saw chain in thecut. Contacting aforeignob-
ject in the wood can also result in loss of
chain saw control.
S Rotational Kickback can occur when the
moving chain contacts an object at the up-
per tip of the guide bar . This contact can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back to-
ward the operator.