Filter
Top Products
10
4. Push the choke/fast idle lever in to the
HALF CHOKE position.
5. Pull the starter rope quickly with your
right hand until the engine starts.
6. Allowtheenginetorunforapproximately
30seconds.Then, squeezeand release
throttletriggertoallowenginetoreturnto
idle speed.
ON/STOP SWITCH
CHOKE/FAST IDLE LEVER
FULL HALF OFF
STARTING A WARM ENGINE
1. Mo veON/ S TOPswitchtotheONposi ti on.
2. Pull the choke/fast i dle lever out to the
HALF CHOKE position.
3. Pull the starter rope quickly with your right
hand until the engine starts.
4. Squeeze and release the throttle trigger
to allow engine to return to idle speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine m ay be flooded if ithas not started
after 10 pulls.
Flooded e ngines can becleared o f excess fuel
by following the warm engine starting proce-
dure l isted above. E nsure the ON/STOP
switch is in the ON position.
Startingcouldrequire m anypulls dependingon
how badly unit is flooded. If engine still fails to
start, refer to TROUBLESHOOTING TABL E
or call 1-800-554-6723.
CHAIN BRAKE
WARNING: If t hebrakeband i sworn
too thin it may break when the chain brake is
triggered. With abroken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by an authorized service
dealer if any part is worn to less than 0.020″
(0.5 mm) thick. Repairs on a chain brake
shouldbemade byan a uthorizedservicedeal-
er . Take your unit to the place of purchase if
purchased from a servicing dealer , or to the
nearest authorized master service dealer.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S The inertia--activated chain brake is
activatedif thefront handguard ispushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengagedbypullingthefronthandguard
back toward the front handle as far as
possible.
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
Disengaged
Engaged
Braking function control
CAUTION:
The chain brake must be
checked several times daily. The engine must
be running when performing this procedure.
This is the only instance when t he saw should
be placed on the ground with the engine run-
ning.
Place the saw o nfirm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing thethrottle t rigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip aroundthe front handle. Thechain
should stop immediately.
Inertia activating function control
WARNING: When performing the
following procedure, the engine must be
turned off.
Grip therear handlewithyourrighthandand
thefronthandlewithyourlefthand. Holdthe
chain sawapproximately 14″(35cm) above
a stump or other wooden surface. Release
your grip on the front handle and use the
weight of the saw to let the top of the guide
bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.
CUTTING METHODS
IMPORTANT POINTS
S Check chain tension before first use and
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLYsection.
S Cut wood only. Do notcut metal,plastics,
masonry, non-wood building materials,
etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary .
S Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
andthusincrease th epossibility o fkickback.