Filter
Top Products
3
S Carefully planyour sawingoperation inad-
vance. Donot startcutting untilyou havea
clear work area,secure footing, and,if you
are felling trees, a planned retreat path.
OPERATE YOUR SAW SAFELY
S Do notoperate achain saw with onehand.
Serious injury to the operator, helpers, by-
standers or any combination of these per-
sons may result from one-handed opera-
tion. A chain saw is intended for
two-handed use.
S Operate the chainsaw only in awell-venti-
lated outdoor area.
S Do not operate saw from a ladder or in a
tree.
S Make sure the chain will not make contact
with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
S Do not put pressure on the saw at the end
of the cut. Applying pressure can cause
you to lose control when the cut is com-
pleted.
S Stop the engine before setting the saw
down.
S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brakeimmediately if itbecomes damaged,
broken or is otherwise removed.
S With the engine stopped, hand carry the
chain saw with the muffler away from your
body , and the guide bar and chain to the
rear, p referably covered with a scabbard.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Have allchain saw serviceperformed by a
qualified service dealer with the exception
of the items listed in the m aintenance sec-
tionofthis manual. For example, ifimprop-
er tools are u sed to r em ove or hold thefly-
wheelwhen s ervicingthe clutch,structural
damage to the flywheel can occur and
cause the flywheel to burst.
S Make certain the saw chain stops moving
when the throttle trigger is released. For
correction, refer to CARBURETOR AD-
JUSTMENT.
S Never modify your saw in any way .
S Keep thehandles dry,clean, andfree ofoil
or fuel mixture.
S Keep fuel and oil caps, screws, and fas-
teners securely tightened.
S Use only Poulan PROR accessories and
replacement parts as recommended.
HANDLE FUEL WITH CAUTION
S Do not smoke while handling fuel or while
operating the saw.
S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
There shouldbe nosmoking, openflames,
or w orkthat couldcause sparks. Allow en-
gine to cool before refueling.
S Mix and pour f uel in an outdoor area on
bare g round; store fuel in a cool, dry , well
ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up all fuel spills before starting saw .
S Move at least 10 feet (3 meters) from fuel-
ing site before starting engine.
S Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.
S Storetheunitand fuelin anareawherefuel
vapors cannot reach sparks or open
flames from w aterheaters, electric m otors
or switches, furnaces, etc.
KICKBACK
WARNING: Avoid kickback which
can result in serious injury . Kickback is the
backward,upward orsudden forwardmotion
of the guide bar occurring when the saw
chain n earthe uppertip of theguide barcon-
tacts any ob ject such as a log or branch, or
when the wood closes in and pinches the
saw chain inthecut. Contacting aforeignob-
ject in the wood can also r esult in loss of
chain saw control.
S Rotational Kickback can occur whenthe
moving chain contacts an object at theup-
per tip of the guide bar. This contact can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back to-
ward the operator.
S Pinch-Kickback can occur when the the
wood closes in and pinches the moving
saw chain in the cut along the top of the
guide bar and the saw chain is suddenly
stopped. This sudden stopping of the
chain results in a reversal of the chain
force used t o cut wood and causes the
saw tomovein theopposite direction ofthe
chain rotation. The saw is driven straight
back toward the operator.
S Pu ll-In can occur when the m oving chain
contacts a foreign object in the wood in the
cut along the bottom of the guide bar and the
saw chain is suddenly stopped. This sudden
stopping pulls the saw forward and away
from the operator and could easily cause the
operator to lose control of the saw .
Avoid Pinch--Kickback:
S Be e xtremely aware of situations or ob-
structions that can cause m aterial topinch
the t op of or otherwise stop the chain.
S Do not cut more than one log at a time.
S Do not twist the saw as the bar is with-
drawn from an undercut when bucking.
Avoid Pull--In:
S Always begin cutting with theengine at full
speed and the s aw housing against wood.
S Use wedges made of plastic or wood.
Never u se metal to hold the cut open.
Kickback Path