Filter
Top Products
5
Symmetrical Guide Bar
Large Radius Tip
S
Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter.Low--
Kickback Chain has met kickback per-
formance requirements w hen tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
Low---Kickback
Chain
Not a Low---Kickback Chain
Can Obstruct Material
Contoured Depth Gauge
Elongated Guard Link
Deflects
kickback force
and allows wood
to gradually ride
into cutter
S
Front Hand Guard, designed to r educe the
chance ofyour left handcontacting thechain
if your hand slips off the front handlebar.
S
Position of front and rear handlebars, de-
signed with distance between handles and
“in-line” with each o ther. The spread and
“in-line” position o f the hands provided by
this design work together to give balance
and resistance in controlling t he pivot of
the saw back toward the operator if kick-
back occurs.
CHAIN BRAKE AND CKA ANGLE
S
Chain Brake, designed to stop the chain in
the event of kickback.
WARNING:
WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac-
tion which throws the bar and rotating chain
back and up toward the operator. Kickback
can be caused by allowing contact of the bar
tip in the danger zone with any hard object.
Kickback canalso becaused bypinching the
sawchain along thetop ofthe guidebar. This
action may push the guide bar rapidly back
toward the operator. Either of these events
may cause you to lose control of the saw
which could result in serious injury or even
death. DONOT RELY UPON ANY OFTHE
DEVICES BUILT INTO YOUR SAW. YOU
SHOULD USE THE SAWPROPERLYAND
CAREFULLY TO AVOID KICKBACK. Re-
duced--kickback guide bars and low--kick-
back saw chains reduce the chance and
magnitude of kickback and are recom-
mended. Yoursawhas a lowkickback chain
and bar as original equipment. Repairs on a
chain brake should be made by an autho-
rized servicing dealer. Take your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master service dealer.
S
Tipcontact insomecasesmaycause alight-
ning fast r ever se REACTION , kicking the
guide bar up and back toward the operator.
S
Pinching the sawchain along the top ofthe
guide bar may push the guide bar rapidly
back toward the operator.
S
Either of these reactions maycause you to
lose control of the saw which could result
in serious injury.Do not rely exclusively
upon thesafety devices built into yoursaw.
WARNING:
Computed kickback
angle (CKA) listed on your saw and listed in
the CKA table below represents angle of
kickback your bar and chain combinations
will have when tested in accordance with
CSA and ANSIstandards. W henpurchasing
replacement bar and chain, considerations
should be given to the lower CKA values.
Lower CKA values represent safer angles to
the user, higher values indicate more angle
and higher kick energies. Computed angles
represented in the non-activated column in-
dicate total energy and angle associated
without activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain brake and resulting kick angle of saw .
In all cases lower CKA values represent a
safer operating environment for the user .
The following guide bar and chain combina-
tions meet kickback requirements of CSA
Z62.1, Z62.3, & ANSI B175.1 when used on
saws listed in this manual. Use of bar and
chain combinations other than those listed is
not recommended and may not meet the
CKA requirements per standard.
Computed kickback angle (CKA) Table
BAR
P/N
Length
CHAIN P/N
16!
MODEL
530044835 952051481
6
_
CKA without chain brake
220
260
18!
530044834 952051480
8
_
NOTE:
If this saw is to be used for commer-
cial logging, a chain br ake isrequired and shall
not be removed or otherwise disabled to com-
ply with Federal O SH A R egulations for Com-
mercial Logging.
SAFETY NOTICE:
Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorder s or