Filter
Top Products
12
The operation of any tractor can result in foreign objects thrown into the
eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your tractor or performing any
adjustments or repairs. We recommend a wide vision safety mask over
spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE
Your tractor is equipped with an operator
presence sensing switch. When engine
is running, any attempt by the operator to
leave the seat without first setting the
parking brake will shut off the engine.
• Depress clutch/brake pedal into full
“BRAKE” position and hold.
• Place parking brake lever in “EN-
GAGED” position and release pres-
sure from clutch/brake pedal. Pedal
should remain in “BRAKE” position.
Make sure parking brake will hold
tractor secure.
Attachment Clutch
Lever “Engaged”
Position
“Disengaged”
Position
Throttle/Choke
Control
Gearshift
Lever
“Brake”
Position
Parking
Brake
“Engaged”
Position
Clutch/
Brake
Pedal
“Disengaged”
Position
STOPPING
MOWER BLADES -
• To stop mower blades,move attach-
ment clutch lever to “DISENGAGED”
position.
GROUND DRIVE -
• To stop ground drive, depress clutch/
brake pedal into full “BRAKE” position.
• Move gearshift lever to neutral (N)
position.
ENGINE -
• Move throttle control to slow position.
NOTE: Failure to move throttle control to
slow position and allowing engine to idle
before stopping may cause engine to
“backfire”.
• Turn ignition key to “OFF” position and
remove key. Always remove key when
leaving tractor to prevent unauthorized
use.
• Never use choke to stop engine.
IMPORTANT: Leaving the ignition
switch in any position other than "OFF"
will cause the battery to be discharged,
(dead).
NOTE: Under certain conditions when
tractor is standing idle with the engine
running, hot engine exhaust gases may
cause “browning” of grass. To eliminate
this possibility, always stop engine when
stopping tractor on grass areas.
CAUTION: Always stop tractor
completely, as described above, before
leaving the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL
Always operate engine at full throttle.
• Operating engine at less than full
throttle reduces the battery charging
rate.
• Full throttle offers the best bagging
and mower performance.
TO MOVE FORWARD AND BACK-
WARD
The direction and speed of movement is
controlled by the gearshift lever.
• Start tractor with clutch/brake pedal
depressed and gearshift lever in
neutral (N) position.
• Move gearshift lever to desired
position.
• Slowly release clutch/brake pedal to
start movement.
IMPORTANT: Bring tractor to a complete
stop before shifting or changing gears.
Failure to do so will shorten the useful
life of your transaxle.
Ignition Key
37
TRACTOR -- MODEL NUMBER 271470
STEERING
KEY PART
NO. NO. DESCRIPTION
1 140044X428 Steering Wheel
2 154427 Axle Assembly STMP Dropped STL
3 156483 Spindle Assembly, L.H.
4 157473 Spindle Assembly, R.H.
5 6266H Bearing, Race, Thrust, Hardened
6 121748X Washer 25/32 x 1-5/8 x 16 Gauge
7 19272016 Washer 27/32 x 1-1/4 x 16 Gauge
8 12000029 Ring, Klip
9 3366R Bearing, Steering Column
10 169832 Draglink
11 10040600 Washer, Lock
13 136518 Spacer Bearing Axle Front
15 145212 Hexflange Lock
17 156546 Shaft Assembly, Steering
18 57079 Washer, Thrust .515 x .750 x .033
19 160395 Support, Shaft
22 165857 Screw, Hex Wshhd
23 165851 Pittman Shaft Assembly
25 154406 Bracket, Steering
26 126847X Bushing, Link, Drag
27 136874 Gear, Sector
28 19131416 Washer 13/32 x 7/8 x 16 Gauge
29 17060612 Screw, 3/8-16 x 3/4
30 76020412 Pin
32 130465 Rod, Tie
36 155099 Bushing, Steering
37 152927 Screw
38 140045X428 Cap, Steering Wheel
39 19133812 Washer 13/32 x 2-3/8 x 12 Gauge
40 7810H Gripco Nut
41 100711L Adaptor, Steering Wheel
42 145054X428 Boot, Steering
43 121749X Washer 25/32 x 1-1/4 x 16 Gauge
44 153720 Shaft Extension Steering
46 121232X Cap, Spindle
47 6855M Fitting, Grease
51 73800500 Nut lock Hex w/Ins 5/16-18
54 74780520 Bolt Fin Hex 5/16-18 UNC x 1-1/4
62 167902 Kit Steering Asm Service
63 74780616 Bolt Fin Hex 3/8-16 x 1-1/4
65 160367 Spacer Brace Axle
66 154404 Bearing Arm Pittman
67 72140618 Bolt, Rdhd Sq 3/8-16 UNC x 2-1/4
68 169827 Axle, Brace
79 19132012 Washer 13/32 x 1-1/4 x 12 Ga.
80 74950612 Bolt Hex Nylon 3/8-16 x 3/4
82 169835 Bracket Susp Chassis Front
85 133835 Fastener Christmas Tree
NOTE: All component dimensions given in U. S. inches
1 inch = 25.4 mm