MTD TBLE Edger User Manual


 
4
Prevent disconnection of the lawn edger powerhead
from extension cord during operation by using a plug-
receptacle retaining strap, connector, or by making a
knot as shown below:
Avoid dangerous environments. Never operate your unit
in damp or wet conditions. Moisture is a shock hazard.
Do not use the unit in the rain. Do not use in or around water.
Do not handle the plug or unit with wet hands or
standing on any wet surfaces.
Do not leave the unit plugged in when not in use, changing
attachments or add-ons, or while being serviced.
WHILE OPERATING
Keep bystanders, especially children and pets, at least
50 ft (15 m) away.
Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty.
Wear heavy, long pants, boots, gloves and a long sleeve
shirt. Do not wear loose clothing, jewelry, short pants,
sandals or go barefoot. Secure hair above shoulder level.
Use the unit only in daylight or good artificial light.
Use the right tool. Only use this tool for the purpose intended.
Do not force unit. It will do the job better and with less
likelihood of injury at a rate for which it was designed.
Use extreme caution when reversing or pulling the unit
towards you.
Do not overreach, take extra care when working on steep
slopes or inclines. Always keep proper footing and balance.
Always hold the unit with both hands when operating.
Keep a firm grip on both the front and rear handle or grips.
Keep hands, face, and feet at a distance from all moving
parts. Do not touch or try to stop the blade when it is
rotating. Do not operate without guards in place.
Do not operate the engine faster than the speed
needed to do the job. Do not run the engine at high
speed when not in use.
Always stop the engine/motor when operation is
delayed or when walking from one location to another.
Stop the engine/motor for maintenance, repair, to
install or remove the blade. The unit must be stopped
and the blade no longer turning to avoid injury.
The blade may become very sharp from use. Always
wear heavy gloves when handling, removing, installing
or cleaning the blade.
If you strike or become entangled with a foreign object, stop
the engine/motor immediately and check for damage. Have
any damage repaired before attempting further operations.
Do not operate unit with a bent, cracked or dull blade.
Discard blades that are bent, warped, cracked or broken.
Stop the unit IMMEDIATELY if you feel excessive
vibration. Vibration is a sign of trouble. Inspect thoroughly
for loose nuts, bolts or damage before continuing. Repair
or replace affected parts as necessary.
Stop and switch the unit to off for maintenance, repair,
or for changing add-ons or other attachments.
Keep unit clean of vegetation and other materials. They may
become lodged between the blade and gearbox or guard.
A coasting blade can cause injury while it continues to
spin after the unit is stopped. Maintain proper control of
the unit until the blade has completely stopped rotating.
Use only genuine factory replacement parts and
accessories for this unit. These are available from
your authorized service dealer. Use of any unauthorized
parts or accessories could lead to serious injury to the
user or damage to the unit, and void your warranty.
MAINTENANCE AND STORAGE
Allow the unit to cool before storing or transporting. Be
sure to secure the unit while transporting.
Store the unit in a locked up and dry or high and dry
place to prevent unauthorized use or damage, out of
the reach of children.
Clean the blade with a hose and water. Wipe the blade
with a light machine oil to prevent rust.
Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use.
Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
Only qualified personnel should perform any repairs or
maintenance procedures that are not described in this
manual.
Check shear bolts, engine mounting bolts and other
bolts at frequent intervals for proper tightness to be
sure the equipment is in safe working condition.
Inside a building store the machine away from ignition
sources. Allow the engine to cool before storing in any
enclosure.
Always refer to the Operator’s Manual instructions for
important details if the lawn edger is to be stored for
an extended period.
Do not attempt to repair the machine unless you have
the proper tools, and instructions for disassembly and
repair of the machine.
SAVE THESE INSTRUCTIONS
RULES FOR SAFE OPERATION
Extension
Cord
Lawn Edgerr
Cord
Lawn Edger
Cord
Extension
Extension
Cord
Cord