MTD 1425NAV Chainsaw User Manual


 
13
12
MAINTENANCE AND REPAIR INSTRUCTIONS
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should
also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require
special tools or skills. If you are unsure about
these procedures take your unit to any non-road
engine repair establishment, individual or
authorized service dealer.
NOTE: Maintenance, replacement, or repair of the
emission control devices and system may be
performed by any non-road engine repair
establishment, individual or authorized service
dealer.
To prevent serious
injury, never perform
maintenance or repairs with unit running.
Always service and repair a cool unit.
Disconnect the spark plug wire to ensure that
the unit cannot start.
WARNING:
MAINTENANCE CHECKLIST
LISTES DES VERIFICATIONS D’ENTRETIEN
LISTA DE VERIFICACION DEL MANTENIMIENTO
EACH USE
CHAQUE
USAGE
CADA USO
HOURS OF
OPERATION
HEURES
D’OPERATION
HORAS DE OPERACION
ITEM / PIECE / PARTE
ACTION / ACTION / ACCION
10
20
SCREWS / NUTS / BOLTS
VIS / ECROUS / BOULONS
TORNILLOS / TUERCAS / PERNOS
AIR FILTER
FILTRE A AIR
FILTRO DE AIRE
FUEL FILTER / OIL FILTER
FILTRE ESSENCE / FILTRE A HUILE
FILTRO DEL COMBUSTIBLE /
FILTRO DE ACEITE
SPARK PLUG
BOUGIE
BUJIA DE ENCENDIDO
SPARK ARRESTER SCREEN
ECRAN PARE-ETINCELLES
PANTALLA DEL PARACHISPAS
FUEL HOSES
DURITS D’ESSENCE
MANGUERAS DE COMBUSTIBLE
CHAIN BRAKE
®
COMPONENTS
COMPOSANTS DE CHAIN BRAKE
®
COMPONENTES DEL CHAIN BRAKE
®
INSPECT / TIGHTEN
INSPECTER / RESSERRER
INSPECCIONAR / APRETAR
CLEAN OR REPLACE
NETTOYER OU REMPLACER
LIMPIAR O REEMPLAZAR
REPLACE
REMPLACER
REEMPLAZAR
CLEAN / ADJUST / REPLACE
NETTOYER / REGLER / REMPLACER
LIMPIAR / AJUSTAR / REEMPLAZAR
INSPECT
INSPECTER
INSPECCIONAR
REPLACE AS REQUIRED
REMPLACER SUIVANT LES BESOINS
REEMPLAZAR SEGUN SE REQUIERA
INSPECT
INSPECTER
INSPECCIONAR
*REPLACE AS REQUIRED
*REMPLACER SUIVANT LES BESOINS
*REEMPLAZAR SEGUN SE REQUIERA
*REPLACE AS REQUIRED
*REMPLACER SUIVANT LES BESOINS
*REEMPLAZAR SEGUN SE REQUIERA
INSPECT
INSPECTER
INSPECCIONAR
*Recommended for Maintenance by an Authorized Service Center Technician.
*Il est recommandé de confier ces opérations à un technicien agréé.
*Recomendamos que el Centro de Servicio Autorizado proporcione el mantenimiento.
A good preventive maintenance program of regular inspection and care will increase life and improve performance of
your chain saw. This maintenance checklist is a guide for such a program.
Cleaning, adjustment, and part replacement may be required, under certain conditions, at more frequent intervals than
those indicated.
OPERATING INSTRUCTIONS
Fig. 11
A
LIMBING
Limbing a tree is the process of removing the branches
from a fallen tree. Do not remove supporting limbs (A)
until after the log is bucked (cut) into lengths (Fig. 12).
Branches under tension should be cut from the bottom
up to avoid binding the chain saw.
BUCKING
Bucking is cutting a fallen log into lengths. Make sure
you have a good footing and stand uphill of the log when
cutting on sloping ground. If possible, the log should be
supported so that the end to be cut off is not resting on
the ground. If the log is supported at both ends and you
must cut in the middle, make a downward cut halfway
through the log and then make the undercut. This will
prevent the log from pinching the bar and chain. Be
careful that the chain does not cut into the ground when
bucking as this causes rapid dulling of the chain.
Fig. 12
Fig. 13
Never cut tree limbs
while standing on a
tree trunk.
WARNING:
When bucking on a slope, always stand on the uphill side.
1. Log supported along entire length: Cut from top
(overbuck), being careful to avoid cutting into the
ground (Fig. 13).
2. Log supported on 1 end: First, cut from bottom
(underbuck) 1/3 diameter of log to avoid splintering.
Second, cut from above (overbuck) to meet first cut
and avoid pinching (Fig. 14).
3. Log supported on both ends: First, overbuck 1/3
diameter of log to avoid splintering. Second, underbuck
to meet first cut and avoid pinching (Fig. 15).
NOTE: The best way to hold a log while bucking is to use
a sawhorse. When this is not possible, the log
should be raised and supported by the limb
stumps or by using supporting logs. Be sure the
log being cut is securely supported.
BUCKING USING A SAWHORSE
For personal safety and ease of cutting, the correct
position for vertical bucking is essential (Fig. 16).
A. Hold the saw firmly with both hands and keep the
saw to the right of your body while cutting.
B. Keep the left arm as straight as possible.
C. Keep weight on both feet.
Fig. 16
Fig. 15
Fig. 14
A
B
C
While the saw is
cutting, be sure the
chain and bar are being properly lubricated.
CAUTION: