Filter
Top Products
10
11
o The trim length selected can be seen through the
hole to the right of the small guide comb (7) and to
the left of the large one (8).
o Thexedguidecomb(6)isnotadjustable.
• Switch on using the on/off button (11) and
commence trimming.
• Switch off using the on/off button after use, remove
head by pressing the two release locks (10) on either
side.
Tips
• Hold trimmer with comb attachment teeth to head,
and move in slow, even movements through the hair.
• Start with sides or neck. Work towards centre of
head. Trim fringe by moving trimmer from forehead
towards centre of head.
• Brush hair cuttings regularly away from head to see
progress.
• Shake hair regularly from trimmer.
• Use the comb supplied (17) to comb hair and the
scissors for minor adjustments which cannot be
done with the trimmer head.
Shaving
• Fit shaving head (5) as described above.
• Switch on using the on/off button (6) and commence
shaving.
• Switch off using the on/off button after use, remove
head by pressing the two release locks on either
side.
Trimming nasal hair
• Fit nasal hair head (4) as described above.
o This head is also suitable for trimming ear hair or
sideburns.
• Switch on using the on/off button (6) and commence
trimming.
• Switch off using the on/off button after use, remove
head by pressing the two release locks on either
side.
Battery charging
• Check apparatus is switched off (on/off button at 0).
• Insert jack on end of cable (1) into socket (13) on
bottom of apparatus.
• Plug in to mains.
o Charge indicator light (12) will show red while
charging and green when battery is fully charged.
o Normal charging takes approx. 12 hours.
• Take the adaptor out of the socket after charging.
• The power cable can also be connected to the
back of the holder (14). The apparatus can then be
charged by placing it in the socket on the top of the
holder.
o The holder is ideal for storing the accessories when
not in use.
NB! For maximum operating time, recharge when
performance becomes noticeably reduced.
CLEANING AND MAINTENANCE
• Brush cutting head and comb attachments using the
small cleaning brush (16) after each use.
• The cutting head can be removed if very dirty for
thorough cleaning.
o Press the buttons on either side to remove the outer
part of the shaving head.
o Clean the blade with a soft brush or by blowing.
o Apply 1-2 drops of lubricating oil, wipe any excess
oil off.
o Replace outer part of head by pressing the buttons
andpushingrmlyintoplace.
• Lubricate the other heads as required: Apply 1-2
drops on cutter and run for approx. 10 seconds.
Remove any excess oil.
• Clean outside of trimmer using a damp cloth. Do not
use detergents of any kind.
• To extend battery lifetime, allow to discharge
completely and then recharge approx. every 3
months.
INFORMATION ON DISPOSAL AND RECYCLING OF
THIS PRODUCT
Please note that this Adexi product is marked with
this symbol:
This means that this product must not be disposed of
together with ordinary household waste, as electrical
and electronic waste must be disposed of separately.
In accordance with the WEEE directive, every member
state must ensure correct collection, recovery, handling
and recycling of electrical and electronic waste. Private
households in the EU can take used equipment to
special recycling stations free of charge. In some
member states you can, in certain cases, return
the used equipment to the retailer from whom you
purchased it, if you are purchasing new equipment.
Contact your retailer, distributor or the municipal
authorities for further information on what you should
do with electrical and electronic waste.
GUARANTEE TERMS
The guarantee does not apply:
• if the above instructions are not followed
• if the apparatus has been interfered with
• if the apparatus has been mishandled, subjected to
rough treatment, or has suffered any other form of
damage
Due to the constant development of our products in
terms of function and design, we reserve the right to
make changes to the product without prior warning.
IMPORTER
Adexi Group
www.adexi.eu
We cannot be held responsible for any printing errors.