Filter
Top Products
SET UP INSTRUCTIONS CONTINUED
TINE ASSEMBLY (Figure 4)
Assemble the inner tine assemblies to the trans-
mission. Secure with clevis and hair pins. The
short end of the tube goes next to the transmis-
sion. Be sure the cutting edge of the blade faces
the direction of rotation. Assemble the out tines
to the inner tine tubes and secure with hair pins
and clevis pins.
FINAL SETUP (Figure 5)
1. Remove the oil ll plug from the engine. With
the unit sitting level, ll the crankcase with oil.
See the engine instruction manual for type and
further directions (Figure 5).
2. Fill the gas tank with clean, fresh, regular
grade gasoline. Do not mix oil and gas.
3. When cranking the unit, be sure no one is
standing in front or near the unit. Check for
proper operation of the clutch lever (see page 7).
Figure 4
Figure 5
GENERAL INFORMATION
The Maxim Chain Drive is the most versatile power unit ever developed for the home gardener and
does a soil preparation job second to none, so a few minutes spent in studying the following instruc-
tions will pay many dividends.
The tiller will dig deeper and move forward slower by pushing down on the handles, and it will go
ahead faster but at a shallower depth by raising up on the handles. The speed of the rotors is con-
trolled by the use of the throttle.
To control the depth of tilling, the tiller must be operated with both the proper throttle speed and cor-
rect up and down hand pressure on the handles. Raising up means going forward. This action
releases the grip of the drag stake in the soil, allowing the tiller to progress ahead. Pushing down
means slowing down or even standing still. This directs the drag stake into the soil, thus holding the
tiller back. Adjust throttle for desired speed of rotors.
When a person is rst learning the proper use of the tiller, it is not unlikely that he will encounter an
uneven or “buckling” action in the operation of this machine. A little practice will accustom the opera-
tor on how to overcome this. Never push on the machine if it has dug itself into a depth of six or more
inches in order to get it to move forward. This is accomplished by slightly raising up on the handles
and tilting the machine slowly from on side to the other.
Your tiller has been carefully designed in both workmanship and material. However, by the very na-
ture of its operation, common sense and caution must be employed at all times. Read carefully and
abide by the safety suggestions stated in this operators guide.
Drive Assembly
Illustration 1
Ref. Part Qty Description Ref. Part Qty Description
1 359328 1 Belt, V-Drive
2 408883 3 Screw, 1/4” - 20 x 1/2” Hex Cap 15 443109 3 Nut 3/8” - NF5 Hex
3 130733 1 Guard 16 359325 1 Lever
4 359383 1 Key, Pulley Mtg. 17 359326 1 Clip
5 271686 1 Pulley, Crankshaft (5 hp) 18 445768 3 Flange Nut, 1/4” - 20 Hex Cap
6 415562 2 Screw, 5/16” - 18 x 5/16”
Socket Head Cap Pt.
19 359321 1 Idler
7 400235 1 Screw, 1/2” x 3/4” Hex Head 20 162069 1 Idler Shaft
8 446145 1 Lock washer, 1/2 Heavy 21 446136 4 Lock washer, 5/16” Heavy
9 162035 1 Belt Guide (Honda 162067) 22 443106 8 Nut, 5/16” - 18 Hex
10 400194 4 Screw, 5/16” x 1 1/2” Hex Cap 23 400112 3 1/4” - 20 x 1 1/4” Hex Head
11 359343 1 Bracket Upper 24 446136 4 Lock washer, 5/16” Heavy
13 336672 1 Pulley 25 443106 1 Nut, 5/16” - Hex
14 359340 1 Bracket Lower 26 400208 4 Screw, 1/4” - 20 x 1 1/4” Hex
8 5